14 CFR Part 91: General Aviation
Accident occurred Monday, November 26, 2012 in Wells, TX
Probable Cause Approval Date: 06/23/2014
Aircraft: CESSNA 421C, registration: N67SR
Injuries: 1 Fatal.
NTSB investigators either traveled in support of this investigation or conducted a significant amount of investigative work without any travel, and used data obtained from various sources to prepare this aircraft accident report.
While in cruise flight, the twin-engine airplane encountered a severe thunderstorm that likely contained hail up to 1.25 inches in diameter. After penetrating the thunderstorm, the airplane’s structure failed, which was evidenced by the pieces of the airplane being found up to 0.6 mile away from the main wreckage. The horizontal tail, which was found 0.25 mile from the main wreckage, had dents on the upper surface that were consistent with in-flight hail damage. The left horizontal stabilizer had failed in an upward direction, and the right horizontal stabilizer had failed in a downward direction, consistent with an extreme left roll rate. In addition, both left and right outboard wing sections were partially separated from the remainder of the wing. Although there was no record of the pilot having obtained a FAA weather briefing, it was not possible to determine if the pilot used other sources to obtain weather information prior to the flight. Records of in-flight communications indicated that the pilot was advised of adverse weather, including thunderstorms and moderate, heavy, and extreme precipitation about 15 minutes before his last transmission. At that time, the airplane was 40 miles from the storm. In addition, the pilot confirmed during communications that the airplane was equipped with on-board weather radar (which provided real-time weather), and the controller authorized him to deviate course, if necessary.
The National Transportation Safety Board determines the probable cause(s) of this accident as follows:
The pilot’s decision to continue the flight into an area of extreme weather, which led to the in-flight encounter with a thunderstorm and structural failure of the wings and tail.
HISTORY OF FLIGHT
On November 26, 2012, about 2124 central standard time, a Cessna 421C airplane, N67SR, was substantially damaged during an in-flight encounter with weather, in-flight separation of airframe components, and subsequent impact with the ground near Wells, Texas. The private pilot, who was the sole occupant, was fatally injured. The airplane sustained impact and fire damage to all major airframe components. The aircraft was registered to H-S Air LP and operated by the pilot under the provisions of 14 Code of Federal Regulations Part 91 as a business flight. Instrument meteorological conditions prevailed for the flight, which operated on an instrument flight rules (IFR) flight plan. The flight originated from the West Houston Airport (IWS), Houston, Texas, about 2040 and was bound for the Richard Lloyd Jones Jr. Airport (RVS), Tulsa, Oklahoma.
Witnesses near the accident site reported hearing an explosion and then seeing a fireball descending through the clouds to the ground.
Radar track data for the last portion of the flight depicted the airplane on a 7720 transponder code. The track showed the airplane initially on a heading of about 20 degrees at 23,000 feet. The track continued in this direction until 2120:03.73 when the airplane began a right turn. The right turn continued for about 30 seconds during which time the altitude remained constant and the heading changed to about 90 degrees. After 2120:45.86, the track showed an erratic steep descent that continued to the end of the data. The final data location was received at 2122:15.53 at an altitude of 2,800 feet. The accident location was 0.86 miles and 94 degrees from the last recorded radar position.
PERSONNEL INFORMATION
The pilot held a private pilot certificate with airplane single-engine land, airplane multiengine land, and instrument airplane ratings. He was issued a third-class airman medical certificate, with a restriction for corrective lenses, on May 8, 2012. According to Federal Aviation Administration (FAA) records, the pilot reported having 2,500 hours total flight experience with 75 hours in the six months preceding his most recent medical examination. The pilot's flight logbook was not recovered during the investigation.
AIRCRAFT INFORMATION
The airplane was a Cessna model 421C, bearing serial number 421C-0257. It was a twin-engine propeller driven monoplane with a retractable tricycle landing gear. Different seating arrangements could be employed with the capability of seating 8 occupants including the 2 flight crew seats. The exact seating configuration of the accident airplane could not be determined due to the extensive impact and fire damage. The airplane was constructed mainly of aluminum alloy materials and had a cantilever main wing arrangement and a pressurized fuselage. Two Continental GTSIO-520-L engines, serial numbers 825011-R and 292480-R, were mounted on each wing and were each capable of producing 375 horsepower.
Maintenance records for the airplane showed that it had accumulated 6736.2 hours total time in service as of its most recent annual inspection dated October 13, 2012. The left and right engines had accumulated 1,039.1 hours, and 1215.1 hours respectively since overhaul as of the date of the annual inspection.
METEOROLOGICAL INFORMATION
No record of the pilot having obtained a Flight Service Station (FSS), or Direct User Access Terminal System (DUATS), weather briefing was found for the accident flight. However, no determination could be made as to whether the pilot obtained weather information from other sources prior to the flight.
An Area Forecast (FA) that included Texas was issued at 2045. The portion of the FA directed toward the southeastern quarter of the northeastern portion of Texas forecasted for times until 0100 the next day: ceiling broken at 3,000 feet msl with cloud tops to 8,000 feet msl and broken cirrus, isolated thunderstorms and light rain with cumulonimbus tops to 38,000 feet. No thunderstorms were forecast for other portions of northeastern Texas.
No Airmen's Meteorological Information (AIRMET) advisories were issued for the accident location at the most recent AIRMET issuance times prior to the accident. The accident site was, however, close to an active AIRMET for IFR conditions issued at 2045.
The Aviation Weather Center in Kansas City, Missouri, issued several Convective Significant Meteorological Information (SIGMET) advisories at 1955 and 2055 that were valid until 2155 and 2255 respectively. These SIGMETs were active for a line of thunderstorms in eastern Texas. The boundaries of the SIGMETs were all near to the accident site. The most recent SIGMET (5C) boundary depicted a 35 mile wide line of thunderstorms that stretched from 30 miles south-southeast of the BELCHER Very High Frequency Omni-Directional Radio Range Tactical Air Navigation Aid (VORTAC), near Shreveport, Louisiana, to 40 miles east of the CENTEX VORTAC near Austin, Texas. The thunderstorm had cloud tops to 45,000 feet and was moving eastward at 20 knots. The accident site was within the boundaries described in the SIGMET.
The National Weather Service (NWS) Surface Analysis Chart for 2100 depicted a low-pressure center at the northwestern Louisiana border with Texas. Associated with the low-pressure center was a cold front that stretched southwestward through the accident region to Mexico, a warm front that stretched southeastward to the Mississippi Gulf coast, and a stationary front that stretched east-northeast.
Station models depicted the wind as northerly behind the cold front in northeast Texas with magnitudes ranging from approximately 10 to 20 knots. Ahead of the cold front the wind was generally southerly with magnitudes near 5 knots. Most station models across eastern Texas depicted clear skies. Temperatures near to and immediately ahead of the cold front were near 70° Fahrenheit (F) with dew point depressions as low as 2°F.
A regional Next-Generation Radar (NEXRAD) mosaic obtained from the National Climatic Data Center (NCDC) for 2120 CST identified a broken line of high (>50 dBZ) values of reflectivity that stretched from central east Texas to northwestern Louisiana. A part of this line was coincident with the accident location.
WSR-88D Level-II base reflectivity weather radar data from Shreveport, Louisiana was obtained. Three-dimensional presentations of base reflectivity isosurfaces from the volume scan initiated at 2116:35 indicated that the accident aircraft penetrated the highest values of reflectivity (> 50 dBZ) during the final portion of its flight and just before its rapid descent. The eastern portion of the 50 dBZ isosurface that rose to a higher altitude was consistent with a convective updraft that may have contained hail. An algorithm utilized by the program GR2Alanlyst (a Nexrad Level II analysis application) to estimate hail stone diameter indicated the potential for 1.25 inch hail in that portion of the storm, and GR2Analyst identified the probability of severe hail (POSH) as high as 84.6 percent.
COMMUNICATIONS
Summaries and transcripts of communications between the airplane and various controlling facilities were obtained from the FAA.
At 2033, the pilot contacted the Houston Intercontinental Airport (IAH) Terminal Radar Approach Control (TRACON), Satellite Clearance Delivery position using his airplane's radio and was issued an IFR clearance from IWS to RVS. The airplane subsequently departed IWS at 2040. The pilot maintained communications with the IAH TRACON until 0257 when he was handed off to the Houston Air Route Traffic Control Center (ARTCC).
At 2057, the pilot checked in with the Houston ARTCC. After establishing communications, the controller cleared the pilot to climb and maintain 23,000 feet. The pilot inquired regarding reports of the cloud tops for the weather he was approaching. The controller advised the pilot that other aircraft were deviating around the weather and that he was working on a route for the airplane to avoid the weather. At 2058, the controller advised the pilot that there were no cloud top reports and then cleared the airplane direct to Longview, Texas, and then direct to Tulsa, Oklahoma. At 2059, the controller disseminated convective SIGMETs 5C and 6C. At 2102, the controller advised the pilot that 23,000 feet would be his final altitude. At 2107, the controller advised the pilot of moderate, heavy, and extreme precipitation 40 miles ahead of the airplane and moving east, and that if the pilot needed to deviate further to the right to let him know. The pilot responded that he was looking at the weather and would let the controller know if he needed to deviate further to the right. Subsequently, at 2113, the pilot requested a 10 degree deviation to the right, which the controller approved. At 2119, the pilot was provided a frequency and advised to contact the Fort Worth ARTCC.
At 2120:28, the Fort Worth controller established communication with N67SR and queried the pilot as to whether the airplane was equipped with a weather radar system on-board. The pilot confirmed having weather radar. The controller then advised the pilot of moderate to heavy precipitation ten miles directly ahead of the airplane's flight path. The pilot acknowledged saying "yes sir", which was the final transmission received from the airplane.
WRECKAGE AND IMPACT INFORMATION
The airplane came to rest in a wooded area near Wells, Texas, in an inverted position with the fuselage oriented in a 220 degree direction. The fuselage and both wings suffered extensive fire damage. The lower fuselage was almost completely consumed by fire. The upper fuselage was recognizable but also had significant fire damage. The landing gear was observed in the retracted position. A baggage door from the nose of the airplane was located about 0.6 miles southeast of the main wreckage.
The vertical stabilizer had impacted a tree on its lower leading edge. It remained attached to the aft fuselage and was predominately intact. The majority of the rudder was not located at the accident scene. The horizontal stabilizer and elevators were separated from the airframe and were located about 0.25 miles south-southwest of the main wreckage. The horizontal stabilizer showed no evidence of fire damage. The left stabilizer was bent in a leading edge upward direction. The forward spar was separated at a location approximately where the fuselage side would have met the spar. The leading one-third of the upper surface of the left stabilizer had numerous dents with a fore-aft component that were consistent with an in-flight encounter with hail. A large portion of the left elevator was missing and was not located at the accident scene. The right stabilizer was bent in a leading edge downward direction and had large portions of its structure missing. Those missing pieces were not located during the on-scene investigation. The remaining structure exhibited evidence of tearing of the outer skin and underlying substructure. The right elevator was predominately intact and remained attached to its hinge locations.
The remains of the outboard right wing came to rest adjacent to the right engine nacelle. The entire wing structure had suffered significant fire damage and was almost completely consumed by fire. The wing tip was positioned next to the engine nacelle while the root portion of the outboard wing was positioned approximately where the wing tip would have normally been. The wing was resting with its upper surface on the ground, the leading edge facing aft, and the trailing edge facing forward relative to the fuselage. The aileron hinge fittings were identified in their normal location. The aileron tip and root were found as was the curved leading edge. The portion of the aileron between the tip and root was not found and is presumed to have been consumed by fire. Examination of the inboard wing spars showed damage consistent with overload failure in a downward direction.
A portion of the outboard left wing was found lying atop the left engine nacelle. A large portion of the left wing was not located; however, the retractable landing light that was located near the wing tip was identified in the wreckage. The missing portions of the left wing were presumed to have been consumed by fire.
Several cuts were made to the control cables by first responders to the accident scene and were discounted during the control system examination. The rudder cables were continuous from the tail cone to their attachment points on the rudder bar bellcranks. One bellcrank on the right rudder bar was separated from the tube at the weld. The break was consistent with the bellcrank arm having been pulled from the tube during the impact sequence. The elevator control cables were continuous from the tail cone to the cockpit. The aft ends of the cables remained attached to the elevator bellcrank attachment points; however the bellcrank itself was fractured. The forward ends of the control cables still had the swaged balls that would have engaged the pulley sector on the forward elevator torque tube within the cockpit. The pulley sector, which is made from aluminum, was partially melted due to fire damage. One cable still remained attached to the remnants of the pulley sector and the other half of the pulley sector was not located and was presumed to have been consumed by fire. One aileron cable remained attached to the interconnect chain, and the cable that would attached to the opposite end of the chain was embedded in melted and re-solidified aluminum within the cockpit. The cables from the interconnect chain were continuous to the bellcrank position located in the center fuselage. The bellcrank was not found and is presumed to have been consumed by fire. Both right side control cables were separated at a location approximately near the outboard side of the engine nacelle. The inboard ends of these cables were continuous to the bellcrank position located in the center fuselage. The outboard ends of these cables were intact and one cable remained attached to the bull-wheel at the aileron. The other cable had been pulled loose from the bull-wheel. The cable separations were consistent with overload failure. The left side control cables were continuous from the bellcrank position in the center fuselage to the outboard ends of the cables. The bull-wheel was not found and is presumed to have been consumed by fire.
The left engine was examined and an attempt was made to rotate the engine. The engine could not be rotated. Subsequently, the engine was disassembled and all internal components examined. The forward engine case near the gear reduction drive was fractured. None of the internal engine components exhibited any preimpact anomalies that would have prevented normal engine operation. The spark plugs exhibited normal burn signatures. The magnetos had impact damage and could not be rotated.
The right engine was examined and the crankshaft was able to be rotated. Compression and suction were verified on all cylinders. The rocker covers were removed and valve action was verified on all cylinders. The spark plugs exhibited normal burn signatures. Both magnetos had impact damage and could not be rotated. No preimpact anomalies were noted that would have precluded normal operation.
MEDICAL AND PATHOLOGICAL INFORMATION
An autopsy of the pilot was performed by Forensic Medical of Texas, Tyler, Texas, on November 28, 2012. The pilot's death was attributed to injuries received in the accident.
Toxicology testing was performed by the FAA Civil Aerospace Medical Institute (CAMI). Testing results were negative for all substances in the screening profile except Atorvastatin detected in Liver. According to CAMI drug information, Atorvastatin is a member of the drug class known as statins, used for lowering blood cholesterol.
NTSB Identification: CEN13FA073
14 CFR Part 91: General Aviation
Accident occurred Monday, November 26, 2012 in Wells, TX
Aircraft: CESSNA 421C, registration: N67SR
Injuries: 1 Fatal.
This is preliminary information, subject to change, and may contain errors. Any errors in this report will be corrected when the final report has been completed. NTSB investigators either traveled in support of this investigation or conducted a significant amount of investigative work without any travel, and used data obtained from various sources to prepare this aircraft accident report.
On November 26, 2012, about 2124 central standard time, a Cessna 421C airplane, N67SR, was substantially damaged during an in-flight encounter with weather, in-flight separation of airframe components, and subsequent impact with the ground near Wells, Texas. The private pilot, who was the sole occupant, was fatally injured. The airplane sustained impact and fire damage to all major airframe components. The aircraft was registered to H-S Air LP and operated by the pilot under the provisions of 14 Code of Federal Regulations Part 91 as a business flight. Instrument meteorological conditions prevailed for the flight, which operated on an instrument flight rules flight plan. The flight originated from the West Houston Airport (IWS), Houston, Texas, at an unconfirmed time and was bound for the Richard Lloyd Jones Jr. Airport, Tulsa, Oklahoma.
Witnesses near the accident site reported hearing an explosion and then seeing a fireball descending through the clouds to the ground.
The airplane came to rest in a wooded area near Wells, Texas. The airplane came to rest in an inverted position with the fuselage oriented in a 220 degree direction. The fuselage and both wings suffered extensive fire damage. The lower fuselage was almost completely consumed by fire. The upper fuselage was recognizable but also had significant fire damage. The landing gear was observed in the retracted position. A baggage door from the nose of the airplane was located about 0.6 miles southeast of the main wreckage.
The vertical stabilizer had impacted a tree on its lower leading edge. It remained attached to the aft fuselage and was predominately intact. The majority of the rudder was not located at the accident scene. The horizontal stabilizer and elevators were separated from the airframe and were located about 0.25 miles south-southwest of the main wreckage. The horizontal stabilizer showed no evidence of fire damage. The left stabilizer was bent in a leading edge upward direction. The forward spar was separated at a location approximately where the fuselage side would have met the spar. The leading one-third of the upper surface of the left stabilizer had numerous dents with a fore-aft component that were consistent with an in-flight encounter with hail. A large portion of the left elevator was missing and was not located at the accident scene. The right stabilizer was bent in a leading edge downward direction and had large portions of its structure missing. Those missing pieces were not located during the on-scene investigation. The remaining structure exhibited evidence of tearing of the outer skin and underlying substructure. The right elevator was predominately intact and remained attached to its hinge locations.
The remains of the outboard right wing came to rest adjacent to the right engine nacelle. The entire wing structure had suffered significant fire damage and was almost completely consumed by fire. The wing tip was positioned next to the engine nacelle while the root portion of the outboard wing was positioned approximately where the wing tip would have normally been. The wing was resting with its upper surface on the ground, the leading edge facing aft, and the trailing edge facing forward relative to the fuselage. The aileron hinge fittings were identified in their normal location. The aileron tip and root were found as was the curved leading edge. The portion of the aileron between the tip and root was not found and is presumed to have been consumed by fire. Examination of the inboard wing spars showed damage consistent with overload failure in a downward direction.
A portion of the outboard left wing was found lying atop the left engine nacelle. A large portion of the left wing was not located; however, the retractable landing light that was located near the wing tip was identified in the wreckage. The missing portions of the left wing were presumed to have been consumed by fire.
Several cuts were made to the control cables by first responders to the accident scene and were discounted during the control system examination. The rudder cables were continuous from the tail cone to their attachment points on the rudder bar bellcranks. One bellcrank on the right rudder bar was separated from the tube at the weld. The break was consistent with the bellcrank arm having been pulled from the tube during the impact sequence. The elevator control cables were continuous from the tail cone to the cockpit. The aft ends of the cables remained attached to the elevator bellcrank attachment points; however the bellcrank itself was fractured. The forward ends of the control cables still had the swaged balls that would have engaged the pulley sector on the forward elevator torque tube within the cockpit. The pulley sector, which is made from aluminum, was partially melted due to fire damage. One cable still remained attached to the remnants of the pulley sector and the other half of the pulley sector was not located and was presumed to have been consumed by fire. One aileron cable remained attached to the interconnect chain, and the cable that would attached to the opposite end of the chain was embedded in melted and re-solidified aluminum within the cockpit. The cables from the interconnect chain were continuous to the bellcrank position located in the center fuselage. The bellcrank was not found and is presumed to have been consumed by fire. Both right side control cables were separated at a location approximately near the outboard side of the engine nacelle. The inboard ends of these cables were continuous to the bellcrank position located in the center fuselage. The outboard ends of these cables were intact and one cable remained attached to the bull-wheel at the aileron. The other cable had been pulled loose from the bull-wheel. The cable separations were consistent with overload failure. The left side control cables were continuous from the bellcrank position in the center fuselage to the outboard ends of the cables. The bull-wheel was not found and is presumed to have been consumed by fire.
The left engine was examined and an attempt was made to rotate the engine. The engine could not be rotated. Subsequently, the engine was disassembled and all internal components examined. The forward engine case near the gear reduction drive was fractured. None of the internal engine components exhibited any preimpact anomalies that would have prevented normal engine operation. The spark plugs exhibited normal burn signatures. The magnetos had impact damage and could not be rotated.
The right engine was examined and the crankshaft was able to be rotated. Compression and suction were verified on all cylinders. The rocker covers were removed and valve action was verified on all cylinders. The spark plugs exhibited normal burn signatures. Both magnetos had impact damage and could not be rotated. No preimpact anomalies were noted that would have precluded normal operation.
IDENTIFICATION
Regis#: 67SR Make/Model: C421 Description: 421, Golden Eagle, Executive Commuter
Date: 11/27/2012 Time: 0324
Event Type: Accident Highest Injury: Fatal Mid Air: N Missing: N
Damage: Destroyed
LOCATION
City: WELLS State: TX Country: US
DESCRIPTION
AIRCRAFT CRASHED UNDER UNKNOWN CIRCUMSTANCES, THE 1 PERSON ON BOARD WAS
FATALLY INJURED, NEAR WELLS, TX
INJURY DATA Total Fatal: 1
# Crew: 1 Fat: 1 Ser: 0 Min: 0 Unk:
# Pass: 0 Fat: 0 Ser: 0 Min: 0 Unk:
# Grnd: Fat: 0 Ser: 0 Min: 0 Unk:
OTHER DATA
Activity: Unknown Phase: Unknown Operation: OTHER
FAA FSDO: DALLAS, TX (SW05) Entry date: 11/27/2012
WELLS, TX (KTRE) - They were first on the scene at the plane crash near Wells Monday night that resulted in the death of an Oklahoma man and still can't believe what they saw.
Sarah Benton was one of the first people on the scene.
"We went through the fence with a cell phone light and a half dead spotlight, and we were walking," Benton said. "There was a strong smell coming like burning; a strong but unfamiliar kind of burning. We eventually ended up walking right up on it, and at that point, you know our adrenaline, our hearts were like going crazy because we were wondering, are there people there?"
The images of the burned plane will be forever embedded in their memory.
"Whenever I got over there, there was nothing left; it's just burnt, everything was burnt - the plane all melted down," Garrett Rogers, an eyewitness to the crash, said. "That's whenever I called the cops."
Deidra Turner said because there were a lot of emergency personnel in the area, they told acquaintances with the Wells Volunteer Fire Department if they were looking for a fire, she and her family thought their pasture was on fire.
"They were like, ‘Well, actually a plane crashed,' and I was like, ‘I seen it explode over our pasture.'"
Once the teens discovered the fire, several law enforcement agencies were everywhere in the wooded area within minutes, taking part in a massive search to find the crash scene. Josh Luellen, a Wells volunteer firefighter, said the scene was "chaotic and busy."
"At first it was pretty hectic because there was so many reports of different areas where the aircraft had went down," Robert Kalka, a Wells volunteer firefighter, said. "Once DPS got there, they completely shut it down and wouldn't let nobody, wouldn't let first responders, fire department in until the FAA got there."
Witnesses said they were hoping that it was just a plane that caught fire, but instantly saw a grim reality.
"All I could see was his clothes, and that's the only spot that was burning was where his clothes were; it looked tan, but it was pretty well crisped over," Rogers said. "It's kind of like a tan color, and all you could see was his boots."
Wesley Mills, another of the first people on the scene, said that he is still in "a little bit of shock" that they found the plane.
http://www.ktre.com
West Houston Airport Director Woody Lesikar said security cameras showed the 64-year-old pilot, John Thomas Steeper, checking in and doing pre-flight checks before taking off.
"He came up to the airplane to unload his luggage, parked the car, and then came in and took care of his obligations and then departed," Lesikar said.
Steeper, of Broken Arrow, Okla., was the only person on board the plane. The plane was registered out of Broken Arrow.
CHEROKEE COUNTY, TX (KTRE) - Tuesday morning, investigators with the Federal Aviation Administration began their investigation of a presumed fatal airplane crash in Cherokee County.
According to DPS, a restricted area has been set up in the area of Cheeseland Road in southern Cherokee County. Authorities said a twin-engine airplane crashed there around 10 p.m. Monday night.
FAA officials arrived at the site early Thursday and will return with other colleagues from Beaumont after sunrise. No one, including local law enforcement, is being allowed near the crash site at this time.
Law enforcement officials who first located the charred wreckage in field said there were no apparent survivors. DPS dispatchers could not determine how many people have died in the crash.
FAA spokesman Lynn Lunsford said the aircraft is likely a Cessna 421, which can accommodate between six and eight passengers. The plane was flying from a west Houston airport to Tulsa-Riverside Airport in Oklahoma. Traffic control lost radio and radar contact with the pilot around 9:30 p.m. as the plane was maneuvering to avoid rough weather in the area.
The plane's tail number is not being released until investigators can confirm it is the aircraft that crash. "The FAA will be a part of a team led by the National Transportation Safety Board, which is in charge of all fatal aircraft accident investigations," Lunsford said. That team is expected to arrive at the scene sometime around 4 a.m. Tuesday.
Lunsford said he does not know how many people are on board.
East Texas teens find plane wreckage using light from cell phone
WELLS, TX (KTRE) - First responders scrambled to find the crash site of a small plane late Monday night in Cherokee County.
As the rain and lightning continued, more crews from all over the Deep East Texas searched for a downed aircraft from Houston that disappeared from radar.
Teenagers from Wells eventually led authorities to the site after they went looking for the plane in a patch of wooded land near their house.
Wesley Mills said his friends ventured out into the rain after noticing something in the sky. "One of my friends went outside, and was like 'the sky's on fire and aint nobody really pay attention to him at first but then we all went outside and sure enough something was falling from the sky."
The group eventually located the wreckage using the light from cell phones, according to Billy Dyson. "We walked pass the little light over there to the right and we were going to keep going and we all stopped and looked back and there was a big ol' fire over there, so we took off running as fast as we could and there was a plane crash right there."
Sarah Benton also joined in the search. "It was mostly just the outline of a plane. You could see where the propeller was and where it was facing, but everything was melted down."
This is a night that these teenagers said they will never forget.
"It hurt, you know what I'm saying because it's some body's life that is probably gone, you know you found it but you just think about their family. It's weird," said Mills.
WELLS, Texas - A twin-engine Cessna 421 en route from West Houston Airport to Tulsa Riverside Airport in Oklahoma has crashed, and a Federal Aviation Administration spokesman said there appears to be no survivors.
Air traffic controllers lost contact with the aircraft about 9:30 p.m. Monday. FAA spokesman Lynn Lunsford says in a news release that the aircraft had been trying to avoid weather near Cherokee County in East Texas when it vanished from radar.
Lunsford said it is not clear how many people had been aboard the airplane. Searchers discovered the aircraft's wreckage in a field near Wells, Texas, late Monday evening.
Lunsford said FAA investigators will join National Transportation Safety Board officials to probe the cause of the crash Tuesday.
http://www.click2houston.com
WELLS, TX -- A twin-engine Cessna 421 en route from West Houston Airport to Tulsa Riverside Airport in Oklahoma has crashed, and a Federal Aviation Administration spokesman says there appears to be no survivors.
Air traffic controllers lost contact with the aircraft about 9:30 p.m. Monday. FAA spokesman Lynn Lunsford says in a news release that the aircraft had been trying to avoid weather near Cherokee County in East Texas when it vanished from radar.
Lunsford says it is not clear how many people had been aboard the airplane. Searchers discovered the aircraft's wreckage in a field near Wells, Texas, late Monday evening.
Lunsford said FAA investigators will join National Transportation Safety Board officials to probe the cause of the crash.
