The accident pilot and a friend flew in the friend's airplane to pick up the accident airplane after recent repairs were completed due to a previous ground loop event in 2016. The accident pilot's friend and the mechanic observed the airplane during the takeoff. The airplane accelerated straight and normal and flew "cleanly" off the turf runway. Shortly after rotation, the airplane rolled left until the airplane impacted trees in a near inverted attitude adjacent to the runway. The mechanic stated that he thought the airplane experienced a departure stall during the takeoff. A postaccident examination of the airframe and engine revealed no evidence of mechanical malfunctions or failures that would have precluded normal operation. The witness observations are consistent with the pilot's loss of control after exceeding the airplane's critical angle of attack during takeoff, which resulted in a power-on, aerodynamic departure stall.
Probable Cause and Findings
The National Transportation Safety Board determines the probable cause(s) of this accident to be:
The pilot's loss of control after exceeding the airplane's critical angle of attack during takeoff, which resulted in an aerodynamic stall.
Findings
Aircraft
Angle of attack - Not attained/maintained (Cause)
Personnel issues
Aircraft control - Pilot (Cause)
Factual Information
History of Flight
Takeoff
Loss of control in flight (Defining event)
Uncontrolled descent
Collision with terr/obj (non-CFIT)
Ren Charles Sagaert
May 30, 1939 - April 12, 2017
Shelby, Michigan
Ren was a proud and longtime member of the Experimental Aircraft Association Chapter 13 since 1971, IBEW Local 58, as well as The Young Eagles Program at Ray Community Airport.
The National Transportation Safety Board traveled to the scene of this accident.
Additional Participating Entities:
Federal Aviation Administration / Flight Standards District Office; Indianapolis, IndianaContinental Motors; Mobile, Alabama
Aviation Accident Final Report - National Transportation Safety Board: https://app.ntsb.gov/pdf
Investigation Docket National - Transportation Safety Board: https://dms.ntsb.gov/pubdms
http://registry.faa.gov/N2377B
Aviation Accident Factual Report - National Transportation Safety Board
Location: Hartsville, IN
Accident Number: CEN17FA152
Date & Time: 04/12/2017, 1250 EDT
Registration: N2377B
Aircraft: TEMCO GC 1B
Aircraft Damage: Substantial
Defining Event: Loss of control in flight
Injuries: 1 Fatal
Flight Conducted Under: Part 91: General Aviation - Personal
On April 12, 2017, about 1250 eastern daylight time, a Temco GC-1B airplane, N2377B, impacted trees and terrain shortly after takeoff from the Williams Flying Field Airport (24IN), Hartsville, Indiana. The commercial pilot sustained fatal injuries, and the airplane sustained substantial damage. The airplane was registered to and operated by the pilot as a Title 14 Code of Federal Regulations Part 91 personal flight. Visual meteorological conditions prevailed at the time of the accident, and a flight plan was not filed. The flight was originating at the time of the accident and was destined for the Shelbyville Municipal Airport (GEZ), Shelbyville, Indiana.
The accident pilot and a friend flew in the friend's airplane to 24IN to pick up the accident airplane. Repairs and maintenance had recently been completed on the accident airplane following a ground loop event in June 2016. After arriving at 24IN, the accident pilot and a mechanic (who was also a pilot) inspected the repairs and reviewed the airplane records. The mechanic provided about 3 to 4 gallons of fuel, which filled the tanks to about 1/2 full. The accident pilot asked the mechanic to perform a few takeoffs and landings with him; the mechanic declined as he had concerns with weight and balance, he was not a flight instructor, and he was unsure of the accident pilot's flight experience. The mechanic suggested the pilot fly to GEZ, which has a longer, hard surface runway, to practice some maneuvers.
Before takeoff, the accident pilot, who had not flown the airplane since the ground loop event, took a few minutes to re-familiarize himself with the cockpit and preflight the airplane. The friend then went to his airplane to prepare for departure. After about 5 minutes, the pilot signaled to the friend that he was experiencing a problem with the radios. In addition, they also noted a "light misfire at idle" with the engine. The pilot performed a brief engine run-up and the misfire was corrected. The pilot and friend then decided to fly to GEZ and resolve the radio issue at that airport and obtain additional fuel. The pilot then taxied ahead of his friend and positioned the airplane to depart on runway 2.
The accident pilot's friend, located in his airplane, and the mechanic, located adjacent to the runway, observed the airplane depart 24IN. According to the friend, the airplane accelerated straight and normal and flew "cleanly" off the ground. Shortly after rotation, about 35 ft above ground level (agl), the airplane rolled left as it continued to climb to about 75 ft agl, at which time the wings were near vertical. The left roll continued until the airplane impacted trees in a near inverted attitude adjacent to the runway.
The mechanic estimated that the airplane rotated about 60 knots, climbed to about 20 ft and then began to roll left; he estimated the airplane struck trees about 85 to 90 knots. He also stated that he thought the airplane experience a departure stall during the takeoff.
Pilot Information
Certificate: Commercial
Age: 77, Male
Airplane Rating(s): Single-engine Land; Single-engine Sea
Seat Occupied: Left
Other Aircraft Rating(s): None
Restraint Used: 4-point
Instrument Rating(s): Airplane
Second Pilot Present: No
Instructor Rating(s): None
Toxicology Performed: Yes
Medical Certification: Class 3 With Waivers/Limitations
Last FAA Medical Exam: 05/31/2016
Occupational Pilot: No
Last Flight Review or Equivalent: 06/19/2015
Flight Time: (Estimated) 1397 hours (Total, all aircraft), 64 hours (Total, this make and model)
The pilot's friend reported that he'd known the pilot for over 25 years. He stated the pilot had over 50 years of flying experience, owned multiple land and amphibian airplanes, and built several experimental airplanes.
The pilot's logbook indicated the pilot had recorded one flight in another airplane for 0.3 hours since the ground loop.
Aircraft and Owner/Operator Information
Aircraft Manufacturer: TEMCO
Registration: N2377B
Model/Series: GC 1B
Aircraft Category: Airplane
Year of Manufacture: 1948
Amateur Built: No
Airworthiness Certificate: Normal
Serial Number: 3677
Landing Gear Type: Retractable - Tailwheel
Seats: 2
Date/Type of Last Inspection: 04/04/2017, Annual
Certified Max Gross Wt.: 1975 lbs
Time Since Last Inspection: 1 Hours
Engines: 1 Reciprocating
Airframe Total Time: 2624 Hours as of last inspection
Engine Manufacturer: Continental
ELT: C91A installed, not activated
Engine Model/Series: IO-360-C
Registered Owner: SAGAERT REN C
Rated Power: 215 hp
Operator: On file
Operating Certificate(s) Held: None
The two-seat, low-wing, retractable-gear tailwheel airplane, serial number 3677, was manufactured in 1948. It was powered by a Continental IO-360-D, 215-horsepower engine, equipped with a controllable-pitch two-blade propeller. The airplane was registered to the pilot on September 12, 2012.
According to the airplane records and the mechanic who performed the repairs, as a result of the ground loop, the airframe, engine, and propeller were all repaired. Airframe repairs were completed on the landing gear system, lower fuselage skin, a wing rib, right flap and right aileron. For transport to the repair facility, the outboard wing sections were removed, and the wing sections and aileron control cable connection were reassembled during the repairs.
The engine was disassembled for a propeller strike inspection and overhauled by a repair station per manufacturer specifications.
According to airworthiness records, the airplane had Cessna 150 seats installed in 1972. Per the records, Cessna factory seat rails and reinforcements were used in the installation.
Meteorological Information and Flight Plan
Conditions at Accident Site: Visual Conditions
Condition of Light: Day
Observation Facility, Elevation: BAK, 656 ft msl
Observation Time: 1245 EDT
Distance from Accident Site: 10 Nautical Miles
Direction from Accident Site: 270°
Lowest Cloud Condition: Clear
Temperature/Dew Point: 15°C / 2°C
Lowest Ceiling: None
Visibility: 10 Miles
Wind Speed/Gusts, Direction: Calm
Visibility (RVR):
Altimeter Setting: 30.4 inches Hg
Visibility (RVV):
Precipitation and Obscuration: No Precipitation
Departure Point: Hartsville, IN (24IN)
Type of Flight Plan Filed: None
Destination: Shelbyville, IN (GEZ)
Type of Clearance: None
Departure Time: 1310 EDT
Type of Airspace: Class E
Airport Information
Airport: Williams Flying Field Airport (24IN)
Runway Surface Type: Grass/turf
Airport Elevation: 745 ft
Runway Surface Condition: Dry
Runway Used: 2
IFR Approach: None
Runway Length/Width: 3200 ft / 150 ft
VFR Approach/Landing: None
Wreckage and Impact Information
Crew Injuries: 1 Fatal
Aircraft Damage: Substantial
Passenger Injuries: N/A
Aircraft Fire: None
Ground Injuries: N/A
Aircraft Explosion: None
Total Injuries: 1 Fatal
Latitude, Longitude: 39.236389, -85.693056 (est)
Examination of the accident site revealed that the airplane impacted several trees and came to rest inverted in a tree-covered ravine. The main wreckage, which consisted of the fuselage, left and right wings, empennage, and engine, came to rest at the base of a large tree. The left wing displayed several semi-circular impacts, consistent with tree strikes. The two-blade propeller hub was fractured and remained partially attached to the crankshaft; both blades were separated from the hub. One propeller blade came to rest adjacent to the forward fuselage, and one propeller blade was located about 150 ft west of the main wreckage. Both propeller blades displayed bending and twisting deformation.
On May 3, 2017, at the facilities of AMF Aviation, Springfield, Tennessee, the National Transportation Safety Board investigator-in-charge, representatives of Continental Motors and the Swift Museum Foundation, LLC, examined the airplane. Examination of the hydraulic power package showed the landing gear valve was in the landing gear extended position. The flap valve was in the flaps retracted position, and the flap actuator rod was extended, which was consistent with a flaps retracted condition. Flight control continuity was established to all flight control surfaces. The aileron balance cable was separated near the center section, and the cable ends were broomstrawed which was consistent with an overload failure. A "Saf-T-Stop" seat track stop was installed on the left seat's right seat track. The seat track stop was secured and no evidence of movement or slippage was noted on the stop or seat track.
The engine was separated from the airframe during recovery from the wooded terrain. The engine oil sump and accessory case were fractured, and wood debris was embedded between the camshaft gear and the crankcase. The fuel system components remained attached to the engine, and the fuel lines remained attached to their respective fittings. The throttle, mixture, and propeller control cables remained attached to their respective components and control levers.
Medical And Pathological Information
On April 13, 2017, at Columbus Regional Hospital, Columbus, Indiana, an autopsy was performed on the pilot. The listed cause of death was blunt force injuries as a result of an accident.
The Federal Aviation Administration's Bioaeronautical Sciences Research Laboratory, Oklahoma City, Oklahoma, performed toxicological testing on the pilot. The tests were negative for cyanide and all screened drugs.
NTSB Identification: CEN17FA152
14 CFR Part 91: General Aviation
Accident occurred Wednesday, April 12, 2017 in Hartsville, IN
Aircraft: TEMCO GC 1B, registration: N2377B
Injuries: 1 Fatal.
This is preliminary information, subject to change, and may contain errors. Any errors in this report will be corrected when the final report has been completed. NTSB investigators either traveled in support of this investigation or conducted a significant amount of investigative work without any travel, and used data obtained from various sources to prepare this aircraft accident report.
On April 12, 2017, about 1310 eastern daylight time, a Temco GC-1B single-engine airplane, N2377B, impacted trees and terrain shortly after takeoff from the Williams Flying Field Airport (24IN), Hartsville, Indiana. The commercial pilot sustained fatal injuries, and the airplane sustained substantial damage. The airplane was registered to and operated by the pilot as a 14 Code of Federal Regulations Part 91 personal flight. Visual meteorological conditions prevailed at the time of the accident, and a flight plan was not filed. The flight was originating at the time of the accident and was destined for the Shelbyville Municipal Airport, Shelbyville, Indiana.
The accident pilot and his friend flew in the friend's airplane to 24IN in order to pick up the accident airplane. Maintenance had recently been completed on the accident airplane as a result of a ground loop event in June 2016. After arriving at 24IN, the accident pilot and a mechanic inspected the repairs and reviewed the airplane records. Prior to the flight, the accident pilot completed a brief engine run-up and then positioned the airplane to depart on runway 2; turf surface, 3,200 ft long, and 150 ft wide.
The accident pilot's friend and the mechanic observed the airplane depart 24IN. The takeoff roll appear normal and shortly after rotation, about 35 ft above ground level, the airplane entered a gradual left roll. The left roll continued until the airplane impacted trees in a near inverted attitude adjacent to the runway.
Examination of the accident site revealed the airplane impacted several trees and came to rest inverted in a tree-covered ravine. The main wreckage, which consisted of the fuselage, left and right wings, empennage, and engine, came to rest at the base of a large tree. The left wing displayed several semi-circular impacts, consistent with tree strikes. The two-bladed propeller hub was fractured and both blades were separated from the hub. One propeller blade came to rest adjacent to the forward fuselage, and one propeller blade was located about 150 ft west of the main wreckage. The airplane was recovered for further examination.
At 1245, the automated weather observing system at the Columbus Municipal Airport (BAK), Columbus, Indiana, located about 10 miles west of the accident site, recorded the following weather conditions: wind calm, sky clear, temperature 15 degrees Celsius, dew point 2 degrees Celsius, and an altimeter setting of 30.40 inches of mercury.
Ren Charles Sagaert
May 30, 1939 - April 12, 2017
Shelby, Michigan
SAGAERT, Ren C. Passed suddenly April 12, 2017. Age 77. Beloved husband of Joyce Sagaert for 48 cherished years. Loving brother of Dan and Jeff (Martha). Dear brother in law of Ed (Elaine) Andreski and Marie Murphy. Loving and adored favorite uncle of many nieces and nephews. Ren was a proud and longtime member of the Experimental Aircraft Association Chapter 13 since 1971, IBEW Local 58, as well as The Young Eagles Program at Ray Community Airport. A Memorial Visitation will be held at Wujek-Calcaterra & Sons Inc., (Shelby) 54880 Van Dyke at 25 Mile Rd arrangements pending.
Read more here: http://wujekcalcaterra.tributes.com
A Michigan pilot who had left his single-engine plane at an airfield near Hartsville last year for repairs died Wednesday when he attempted to fly the vintage aircraft home.
The 1948 Temco Swift aircraft crashed into a treeline near the Williams Flying Field at 12:52 p.m. near Anderson Falls in the Hartsville area, Bartholomew County Sheriff Matt Myers said.
The pilot, identified as 77-year-old Ren Sagaert of Shelby Township, Michigan, was the sole occupant of the plane and was pronounced dead at the scene, Coroner Clayton Nolting said. An autopsy is scheduled for today, he said.
The plane has been registered since September 2012 to Sagaert, who lived north of Detroit, FAA records state.
Sagaert had just taken off in the plane from a private grass airstrip at 20950 E. County Road 200N when the crash occurred, investigators said. The airstrip is owned by Mike Williams, who does engine work on small planes from his shop, about three-quarters of a mile north of County Road 200N.
The Sagaert plane had been in a mishap that damaged its landing gear in June 2016, and Sagaert had the plane shipped to Williams for repairs, said Steve Wilson, a retired National Transportation Safety Board investigator. Wilson knows Williams and spoke with him Wednesday afternoon a few hours after the crash, he said.
Williams had completed the repairs by January and Sagaert told him he would pick it up in April, Wilson said.
Williams told Wilson he had offered to do a flight test on the plane several times, but Sagaert declined, saying he would fly it when he arrived to pick it up, Wilson said.
Williams had taxied the plane around the airfield, testing the engine and brakes, but had not tested the plane in the air, Wilson said.
WHAT HAPPENED
When Sagaert took off on Wednesday, the engine was running strong, but the landing gear of the tail-wheel aircraft remained down, which was unusual, Wilson said after talking with Williams. The airplane took a sharp turn to the left and flipped upside down, going into the tree line, Williams told Wilson.
Although a witness had told Bartholomew County Sheriff’s deputies the engine ran strong, then cut out before the crash, Williams told Wilson the engine continued to run as the plane crashed after an abrupt left turn and flipped over.
Wilson said the plane at liftoff would have been traveling 60 to 65 mph, accelerating to a speed of 90 to 100 mph as it climbed into the air.
Wilson said Williams told him that landing gear retraction tests had been done and Williams was unsure why the gear did not retract as it should have.
Sagaert’s body was removed from the scene shortly before 3 p.m. Wednesday in an unmarked coroner’s vehicle.
Media was not allowed at the crash scene as investigators waited for the NTSB investigators to arrive and begin the investigation.
Although the plane did not catch fire upon crashing, some fuel leaked from its 56-gallon fuel tank, Columbus Fire Department Deputy Chief Andy Lay said.
Measures had to be taken so fuel did not leak into the nearby Fall Fork of Clifty Creek, he said.
Jim Fritsche, who lives just west of the airstrip, told investigators he heard the engine start as if it were taking off, but then heard it cut out, followed by a loud bang. A witness went to the wooded crash site to give aid, but it’s believed the pilot died instantly, Myers said.
With sunshine and a cool northerly breeze, conditions were ideal for flying, said Tom Earnhart of Hope, a licensed pilot and a friend of Williams. In addition, the freshly mowed grass airstrip was in good shape, Earnhart said.
The plane that crashed near Hartsville is believed to involve one of only about 300 Temco Swift aircraft still flying, said Pam Nunley, executive director of the Swift Museum Foundation of Athens, Tennessee.
Wilson, who owns two Swift planes and is rehabbing two others at his home in Granbury, Texas, said he did not know Sagaert.
Wilson said Williams also owns a Swift, along with doing work repairing them for other pilots.
PLANE HISTORY
Most of the Swift aircraft were built from 1946 to 1951 in Fort Worth or Dallas, Texas, marketed as a recreational opportunity for returning World War II pilots, Nunley said. The museum foundation has about 700 members who keep in touch about their planes and build friendships through their passion for this particular type of aircraft, Nunley said.
“We like to think of it as being a family here at the foundation,” Nunley said. “These people are all friends with each other.”
Wilson said the all-metal, two-seat Swift planes, a tail-wheel aircraft, can travel at about 145 to 165 miles per hour at a maximum height of about 16,000 feet, and almost all of the planes still flying have modified engines to increase their horsepower.
The all-grass airfield that Williams uses would be adequate for a Swift plane to take off or land, Wilson said, as the planes need about 1,000 feet and do not require pavement runways. Williams’ airfield has a 3,200-foot area for takeoffs and landings, Wilson said.
“It’s not a hard airplane to fly, but it’s not for a beginner,” said Wilson, 77.
Wilson said the NTSB will likely spend several days at the crash site and it will be up to a year before a written report on the accident is issued. The agency will likely issue a preliminary accident report in about 10 days, he said.
About the Temco Swift
General specifications of the Temco Swift airplane
Seats: 2 (1 crew, 1 passenger)
Classification: Tail-wheel, low-wing aircraft
Engines: 1
Engine power: 125 hp, although many engines have been modified to 145 to 165 hp by owners.
Maximum speed: 185 mph
Cruising speed: 140 mph
Height: 6 feet, 2 inches
Length: 20 feet, 10 inches
Empty weight: 1,370 pounds
Maximum weight: 1,975 pounds
Production: 1946-1951, with about 1,100 produced in Fort Worth, Texas and 400 in Dallas, Texas
Source: flugzeuginfo.net, an online civil and military aircraft encyclopedia and Swift Museum Foundation, Athens, Tennessee
Fatal air crashes in Bartholomew County
Wednesday’s aviation fatality is the third in Bartholomew County in the past 15 years.
Pilot Gerald H. Clayton, 81, of Columbus, died Aug. 2, 2013, which was eight days after his two-seat plane crashed into a home on the north side of Columbus. Clayton, an experienced pilot, and passenger Dennis King, 60 at the time and also from Columbus, both suffered burns from flames that ignited during the crash.
Mukesh K. Gupta of Macon, 25, a commercial pilot from Georgia, died in an air crash on July 18, 2002, when a twin-engine Piper PA-60 cargo plane, operated by Grand Aire Express, was destroyed in the early morning when it crashed in thick fog.
Original article can be found here: http://www.therepublic.com
HARTSVILLE, Ind. – Authorities say the pilot of a small plane was killed in a crash in Bartholomew County on Wednesday afternoon.
Thee crash occurred at 20950 E County Rd 200 N which is about three miles south of Hartsville just before 1 p.m.
Investigators believe the pilot, 77-year-old Ren Sagaert of Shelby Township, Michigan, was taking off in his 1940s Temco Swift plane at the time of the crash. He was pronounced dead at the scene. No other injuries were reported.
An autopsy is scheduled for Thursday.
The crash is being investigated by the Bartholomew County Sheriff’s Office, Indiana State Police and the Federal Aviation Administration.
Source: http://fox59.com
No comments:
Post a Comment