Wednesday, January 13, 2016

Beech B36TC Bonanza, N4BA: Fatal accident occurred April 1, 2010 at Dayton-Wright Brothers Airport (MGY), Dayton, Montgomery County, Ohio

National Transportation Safety Board - Aviation Accident Final Report: http://app.ntsb.gov/pdf

Docket And Docket Items -  National Transportation Safety Board:   http://dms.ntsb.gov/pubdms

Aviation Accident Data Summary  -   National Transportation Safety Board:   http://app.ntsb.gov/pdf

NTSB Identification: CEN10FA180
14 CFR Part 91: General Aviation
Accident occurred Thursday, April 01, 2010 in Dayton, OH
Probable Cause Approval Date: 06/20/2011
Aircraft: BEECH B36TC, registration: N4BA
Injuries: 2 Fatal.

NTSB investigators either traveled in support of this investigation or conducted a significant amount of investigative work without any travel, and used data obtained from various sources to prepare this aircraft accident report.

Approximately 1 minute after takeoff, as the airplane was about 1 mile southwest of the airport, the pilot reported an engine failure to air traffic controllers and initiated a return to the airport. One witness, located about 1 mile west of the airport, reported that the sound of the engine changed abruptly; noting that the engine seemed to lose power completely. Another witness, located near the airport, observed the airplane approach from the west and turn to align with the downwind runway. During the turn, the left wingtip struck the ground and the airplane impacted short of the runway. A postimpact fire ensued. Although the pilot initiated a return to the airport, an interstate highway and an open grass area short of the runway were both potentially available for an emergency landing. A postaccident examination of the engine revealed that the No. 1 (aft) main crankshaft bearing failed due to unknown circumstances. The progressive failure of the bearing likely precipitated secondary failures of the crankcase through-bolt and the fuel pump coupling, which resulted in a complete loss of engine power.

The National Transportation Safety Board determines the probable cause(s) of this accident as follows:
The complete loss of engine power due to failure of the No. 1 main bearing, and the secondary failure of a crankcase through-bolt and the fuel pump drive coupling. Contributing to the accident was the pilot's decision to attempt a return to the airport for a downwind forced landing, despite having an interstate highway and an open grass area short of the runway as available emergency landing sites.

HISTORY OF FLIGHT

On April 1, 2010, at 1253 eastern daylight time, a Beech B36TC Bonanza, N4BA, impacted terrain short of the runway during a forced landing following a loss of engine power at the Dayton-Wright Brothers Airport (MGY), Dayton, Ohio. A post-impact fire ensued and the airplane was destroyed. The pilot and sole passenger on-board sustained fatal injuries. The airplane was registered to Poelking LLC and operated by the pilot under the provisions 14 Code of Federal Regulations Part 91 on an instrument flight rules (IFR) flight plan. Visual meteorological conditions prevailed. The flight departed from MGY about 1250. The intended destination was DuPage Airport (DPA), West Chicago, Illinois.

The pilot initially contacted Dayton Approach Control while he was on the ground at MGY and requested an IFR clearance to DPA. However, before a clearance was issued, the pilot informed the controller that he needed to return to the ramp due to a magneto problem. Thirty minutes later, the pilot again contacted Dayton Approach while on the ground at MGY and requested a clearance to DPA. A clearance was issued at 1248 and the flight was released for takeoff at 1249.

At 1251:11 (hhmm:ss), the pilot contacted Dayton Approach Control. He informed the controller that they were airborne and climbing through 1,300 feet mean sea level (msl). At 1251:32, the controller replied that radar contact was established 1 mile south of MGY. However, 14 seconds later, the pilot stated that he was “going to circle around for a landing” at MGY because a “compartment [had] come open.” The controller acknowledged and cleared the flight to return to MGY. At 1252:16, the pilot stated that he was declaring an emergency due to an engine failure.

Radar data depicted the airplane tracking the Runway 20 extended centerline after takeoff. The initial radar data point was recorded at 1251:05 and indicated that the airplane was near the departure end of Runway 20 at 1,300 feet msl. About 1251:42, the airplane entered a right turn and remained in that turn until the final data point, which was recorded at 1252:46. At that time, the airplane was approximately 1/2 mile southwest of the Runway 2 threshold at 1,200 feet msl, and on an approximate magnetic course of 094 degrees. The radar track data indicated that the airplane was within 1/4 mile of an interstate highway during the right turn.

A witness reported that she was working in her yard, about 1 mile southwest of the airport, when the accident airplane flew over. Initially, the sound of the engine was completely normal. However, the routine engine sound changed abruptly, noting that the engine seemed to completely cut out. She added that the engine did not sputter, or increase and decrease pitch, during that time. The change in engine sound caused her to look up. She reportedly observed the airplane in a right turn with an estimated bank angle of 45 degrees. The airplane was heading northwest when she first saw it. It remained in that right turn until she lost sight of it, at which time it was on an easterly heading. She added that nothing about the airplane seemed unusual except for the abrupt change in the engine sound and a lower than normal flight profile.

Additional witnesses reported observing the airplane approach the airport from the west with the landing gear in the retracted position. They stated that the airplane banked to the left in an apparent attempt to line-up with runway 2. The left wingtip struck the ground and the airplane impacted an open grass area south of the runway. A post impact fire ensued.

PERSONNEL INFORMATION

The pilot, age 50, held a private pilot certificate with airplane single engine land and instrument airplane ratings. He was issued a third-class airman medical certificate on March 26, 2009, with a restriction for corrective lenses. FAA records indicated that the pilot added an instrument rating to his private pilot certificate on August 31, 2009.

The pilot’s flight time logbook was not available to the NTSB. On his instrument rating application, the pilot noted a total flight time of 182.5 hours, with 102.7 hours of instruction received. He reported a total of 93.1 hours in B36TC airplanes at the time of that exam.

AIRCRAFT INFORMATION

The accident airplane was a 1983 Beech B36TC (Bonanza), serial number EA-356. It was a six-place, single-engine airplane, with a retractable tricycle landing gear configuration. The airplane was powered by a 300-horsepower Continental TSIO-520-UB turbo-charged engine, serial number 515941. It was equipped with a 3-bladed, constant speed (adjustable pitch) McCauley model 3A32C406 propeller assembly, serial number 983648.

Maintenance records indicated that an annual inspection was completed on March 11, 2010, at a total airframe time of 2,283.9 hours. The records noted that the engine had accumulated 997.8 hours since overhaul at the time of the annual inspection. There was no record of maintenance issues subsequent to the annual inspection.

Maintenance records also indicated that aluminum fragments were found in the filter during an oil change conducted in July 2009. The engine was disassembled as a result and several piston pins were found to be frozen. The connecting rods were repaired and new cylinders were installed. The airplane was subsequently returned to service with no further issues noted.

METEOROLOGICAL CONDITIONS

Weather conditions recorded by the MGY Automated Surface Observing System (ASOS) at 1253 were: Clear skies; 10 miles visibility; winds from 210 degrees at 9 knots, gusting to 22 knots; temperature 22 degrees Celsius; dew point 9 degrees Celsius, altimeter 29.98 inches of mercury.

AIRPORT INFORMATION

Dayton-Wright Brothers (MGY) was a non-towered airport; served by a single runway. Runway 2-20 was 5,000 feet long by 100 feet wide and constructed of asphalt. The approach area to Runway 2 consisted of an open grass area extending approximately 1,000 feet from the threshold. A localizer antenna was located in this area on the runway centerline about 900 feet from the threshold. 

The east side of Runway 2 was bordered by an open grass area about 500 feet wide. Commercial/business areas bordered the airport to the south. Residential areas bordered the airport to the east. A residential area was located about 1,200 feet east of the Runway 2 threshold, with an open grass area between the threshold and the nearest residences.

WRECKAGE AND IMPACT INFORMATION

Initial ground impact was on the airport property about 860 feet south-southwest of the Runway 2 threshold. The debris path was oriented on an approximate 024-degree magnetic bearing. The main airplane wreckage, which consisted of the fuselage, engine, empennage, and wings, came to rest about 179 feet from the initial impact point. Grass scorched by the post impact fire extended to approximately 120 feet north-northeast of the main wreckage.

The nose section of the airplane was fragmented. The upper portion of the fuselage and aft fuselage structure remained. The lower fuselage was consumed by the postimpact fire. The engine had separated from the airframe. It came to rest inverted with the main wreckage. The propeller assembly was separated from the engine crankshaft flange. The propeller blades remained attached at the hub. The left wing tip separated from the airframe and came to rest about 75 feet south of the main wreckage. The empennage was partially separated from the aft fuselage. The vertical stabilizer, with the rudder attached, had separated from the empennage. The flight controls and flaps sustained damage consistent impact forces and the postimpact fire.

No anomalies consistent with a pre-impact failure or malfunction of the airframe were observed. A teardown examination of the engine was conducted subsequent to the accident. (A summary of those findings is included later in this report.) 

MEDICAL AND PATHOLOGICAL INFORMATION

An autopsy of the pilot was performed by the coroner’s office of Montgomery County, Ohio, on April 5, 2010. The FAA Civil Aerospace Medical Institute forensic toxicology report was negative for all substances in the screening profile.

TESTS AND RESEARCH

Teardown examination of the engine revealed that the #1 (aft) main bearing had failed. Specifically, the right half of the #1 main bearing was fractured into 5 pieces. A portion of the right bearing was located under the left bearing. In addition, the lower, aft crankcase through-bolt was fractured near mid-length. Finally, the fuel pump drive coupling and the standby alternator drive shaft were fractured.

Metallurgical examination of the #1 main bearing revealed damage consistent with contact of the fracture faces between other bearing sections. No fracture features were visible.

The crankcase through-bolt was fractured at one of the o-ring grooves at the case split line. The adjacent o-ring was hardened and partially charred. The cadmium surface plating was bubbled and solidified into surface beads on either side of the split line. The fracture surface exhibited features and deformation patterns consistent with bending over-stress. The overstress region appeared to emanate from a crescent-shape area that exhibited intergranular separation. Cadmium was identified on portions of the crescent-shaped area.

The fuel pump coupling was fractured at the reduced diameter shear section. The fracture surface exhibited crack arrest lines and surface topography consistent with high-stress reverse bending fatigue. The standby alternator driveshaft was also fractured at a reduced diameter section. Otherwise, the driveshaft appeared straight and undamaged. The fracture surface exhibited features consistent with rotational bending fatigue fracture.

ADDITIONAL INFORMATION

The Director of Maintenance at the fixed base operator (FBO) met the accident pilot when he returned to the ramp with a rough magneto. The pilot informed the maintenance director that the drop in engine speed exceeded limitations on one of the magnetos, and that he did not observe any drop on the second magneto.

The maintenance director got in the airplane and conducted a run-up. He stated the engine started without hesitation, and went to 1,200 or 1,300 rpm. He conducted at least two magneto checks and the drop in engine speed was about 100 rpm. Engine operation was smooth the entire time.

The pilot reportedly commented to the mechanic that he had been idling for a long time and had not leaned the mixture. He noted that he did not observe any issues with the operation of the engine or the magnetos during the time he was in the airplane.

The airplane flight manual specifies a maximum drop in engine speed of 150 rpm during a magneto check.

Airport records indicate that the accident airplane was fueled with 61.6 gallons of 100 low lead aviation fuel about 1815 on March 31, 2010; the evening prior to the accident flight.


Tom Hausfeld and his daughter Kacie were killed April 1, 2010, when the plane he was piloting crashed at Dayton-Wright Brothers Airport just after takeoff.
~

DAYTON —

Dayton Flyers volleyball coach Tim Horsmon remembers Kacie Hausfeld as one of the most well-liked players on the team when he coached her as a freshman in 2007. Her teammates respected her. She competed. She was smart.

“She was an unbelievable kid,” Horsmon said.

Hausfeld, 21, died with her dad Tom, 50, in a plane crash on April 1, 2010, at Dayton-Wright Brothers Airport. The single-engine plane Tom was piloting crashed after takeoff on the way to Chicago.

In the years since, Kacie’s memory has lived on at UD. The team presents the Kacie Hausfeld Teammate Award every season. Now, a $1.2 million gift to the volleyball program by her mom Lori Hausfeld and the family will help preserve her legacy even longer.

The Dayton volleyball program held a special place in the family’s heart then and still does today.

“I’ve thought about doing something for the last few years,” Hausfeld said. “The university has been so important to me. It was very important to Kacie and Tom. They loved the school. Even after the accident, (UD was) just so supportive. I wanted something to give back to UD because they gave so much back to me and my daughter.”

The money will allow the program to do a number of things at the Frericks Center, such as upgrading the seating and the sound system. UD also plans to build a team lounge. It will be named after Kacie, an Alter High School graduate.

“She was such a social kid,” Horsmon said. “That’s going to be a great spot to remember her.”

Hausfeld, of Springboro, said when she first approached UD about making a donation, the university figured she was talking in the $100,000 to $200,000 range. She shocked UD when she told them she was thinking bigger — much bigger.

“They’re like, ‘That’s fantastic,’” Hausfeld said.

Tom Hausfeld was a successful businessman. He retired in 2006 after selling his business, Auto Disposal Systems Inc., of Dayton. He was well known for his charitable giving before his death.

Horsmon’s return to Dayton helped spur Hausfeld’s donation. He left for the head coaching job at the University of Maryland in the spring of 2008. Kacie played her final two seasons for Kelly Sheffield. Horsmon came back to the Flyers in December 2013, and at his first home match in 2014 against Nebraska, he saw Hausfeld in the stands.

“I turned around at the beginning of the match,” Horsmon said. “I don’t now why. I never really look behind the bench. I saw Lori. she caught my eye. We waved. I got a hold of her after the match and said, ‘Let’s go grab some lunch.’

“I hadn’t really had a chance to sit down with her after what happened with Kacie and Tom and share how I was feeling, that I wished I were here during that time. I think that turned into her wanting to do something for the program and her doing something in Kacie’s memory.”

Dayton already has a successful volleyball program. The Flyers have won the Atlantic 10 regular-season title 12 times since 1998 and have won the conference tournament a league-record 10 times. They made their 11th NCAA tournament appearance in 2015.

The gift, Horsmon said, “allows us to show a commitment to our volleyball program and our players that not too many other programs get to do. When we’re recruiting against Big Ten programs and SEC and ACC And Big 12, it puts us in that arena with what they’re doing. It’s a special donation. It’s a special opportunity.”

Source: http://www.mydaytondailynews.com


Tom & Kacie Hausfeld


Tom Hausfeld and his daughter Kacie.

Lori, Kacie, Ali and Tom Hausfeld (left to right) are pictured. Tom Hausfeld, 50, and his daughter Kacie, 21, were killed April 1, 2010 when the plane he was piloting crashed at Dayton-Wright Brothers Airport just after takeoff.


No. 14 Kacie Hausfeld, of Dayton, sets the ball against St. Louis in 2009. Kacie died in a plane crash April 1, 2010.
~










No comments:

Post a Comment