Tuesday, February 09, 2016

Cessna 152, N555UF, United Flight Systems: Fatal accident occurred November 17, 2013 in Spring, Texas

NTSB Identification: CEN14FA057 
14 CFR Part 91: General Aviation
Accident occurred Sunday, November 17, 2013 in Spring, TX
Probable Cause Approval Date: 02/08/2016
Aircraft: CESSNA 152, registration: N555UF
Injuries: 2 Fatal.

NTSB investigators either traveled in support of this investigation or conducted a significant amount of investigative work without any travel, and used data obtained from various sources to prepare this aircraft accident report.

The purpose of the night instructional flight was to in remain in the airport traffic pattern and practice touch-and-go landings. According to air traffic control data, during the initial climb following the second touch-and-go landing, the flight instructor told the tower controller that the airplane was experiencing “engine problems” and requested to make an immediate 180-degree turn back to the airport for landing. Based on available radar data, the airplane was likely less than 250 ft above the ground when the flight instructor reported the engine problem. A witness reported that, while the airplane was on the downwind leg for the first landing, the engine sounded abnormal and that the engine continued to run roughly while the airplane was on initial climb following the second landing. Several witnesses reported seeing the airplane in a steep left turn before it entered a near-vertical descent into terrain. A postaccident airframe examination did not reveal any malfunctions or failures that would have precluded normal operation. The carburetor heat control was found in the “off” position. Control cable continuity was confirmed between the carburetor heat box and the cockpit control; however, impact damage to the carburetor air box precluded a determination of whether the carburetor heat was activated at the time of the accident. Although the weather conditions at the time of the accident were conducive to the formation of carburetor ice at reduced engine power settings, the investigation was unable to determine to what extent carburetor ice might have formed during the accident flight. 

Additionally, disassembly of the carburetor revealed that one of its two hollow polymer floats was flooded with fuel, which would reduce the buoyancy of the float and could result in poor idle power performance and/or possible flooding of the carburetor. During the 5 years preceding the accident, the carburetor manufacturer issued multiple service bulletins (SB) that acknowledged that the hollow polymer float design had known issues with fuel leaking into the float through a welded seam. The carburetor manufacturer specified that all affected carburetors should be inspected within 30 days and then at 30-day intervals until the affected floats were replaced with an updated solid-epoxy float design that was impervious to flooding. Owner/operator compliance with the service bulletins was considered optional under FAA regulations. According to maintenance documentation, the accident carburetor had not been inspected as specified by the SBs.

Ultimately, the root cause for the partial loss of engine power could not be identified because the investigation was unable to determine to what extent carburetor icing, the flooded float, or a combination of the two conditions could have contributed to the loss of engine power. Following the partial loss of engine power, it is likely that the flight instructor failed to maintain airspeed during the turn back to the airport, which resulted in an aerodynamic stall.

The National Transportation Safety Board determines the probable cause(s) of this accident as follows:
The flight instructor's failure to maintain airspeed following a partial loss of engine power for reasons that could not be determined during postaccident examination, which resulted in an aerodynamic stall and subsequent loss of airplane control.

HISTORY OF FLIGHT

On November 17, 2013, at 1915 central standard time, a Cessna model 152 airplane, N555UF, was substantially damaged during a forced landing at the David Wayne Hooks Memorial Airport (DWH), Spring, Texas. The flight instructor and student pilot were fatally injured. The airplane was registered to WBR Interests LLC and operated by United Flight Systems, under the provisions of 14 Code of Federal Regulations Part 91, without a flight plan. Night visual meteorological conditions prevailed for the local area training flight that had departed DWH at 1900.

According to air traffic control (ATC) data, the purpose of the instructional flight was to remain in the airport traffic pattern to practice night takeoffs and landings. At 1900:22, the tower controller cleared the accident flight for takeoff and to remain in a left traffic pattern for touch-and-go landings on runway 17R (7,009 feet by 100 feet, asphalt). The accident airplane was first observed on radar about 150 feet above ground level (agl) while on the upwind leg. The airplane continued to make left traffic for runway 17R before being cleared for the first touch-and-go landing at 1904:42. At 1906:48, the airplane descended below available radar coverage while on a 1/4 mile final for runway 17R. The airplane reemerged on radar at 1908:15, about 1/4 mile south of the runway departure threshold at about 250 feet agl. The airplane continued to make left traffic for runway 17R before being cleared for the second touch-and-go landing at 1911:08. At 1913:48, the last radar return was recorded for the accident flight about 1/3 mile north of the runway approach threshold at about 150 feet agl. At 1914:41, the flight instructor told the tower controller that they were having "engine problems" and requested to make a 180-degree turn back to the airport for a landing. At 1914:47, the tower controller cleared the flight for the 180-degree turn back landing. Based on available information, the airplane had completed the second touch-and-go landing and was on initial climb when the flight instructor reported the loss of engine power. At 1914:51, there was an open-microphone transmission from the accident airplane that comprised of "No, No, My." No additional transmissions were received from the accident flight.

The tower controller reported that after he cleared the flight for the 180-degree turn back landing, he saw the airplane enter a steep left bank and descend nose-down into the terrain located on the east side of the airport.

Another witness reported hearing the accident airplane while it was on a left downwind leg for runway 17R and remarked that the sound of the engine was abnormal. The same witness reported that the engine continued to run rough while the airplane was on initial climb following the second touch-and-go landing. Several witnesses to the accident reported seeing the accident airplane in a steep left turn before it entered a near vertical descent into terrain. Two of these witnesses reported seeing the wingtip navigation and strobe lights in a near vertical line, indicating a near 90-degree bank angle, before the airplane banked past 90-degrees and descended nose-down into the terrain.

PERSONNEL INFORMATION

--- Flight Instructor ---

According to Federal Aviation Administration (FAA) records, the flight instructor, age 22, held a commercial pilot certificate with single and multi-engine land airplane and instrument airplane ratings. He also held a flight instructor certificate with single engine airplane and instrument airplane ratings. His last aviation medical examination was completed on May 23, 2013, when he was issued a second-class medical certificate with no limitations or restrictions. A search of FAA records showed no previous accidents, incidents, or enforcement proceedings. His last flight review, as required by FAA regulation 61.56, was completed upon the reissuance of his flight instructor certificate dated September 6, 2013.

The flight instructor's flight history was reconstructed using pilot logbook information and employment documentation. He had been employed by the airplane operator, United Flight Systems, since October 11, 2013. His most recent pilot logbook entry was dated November 15, 2013, at which time he had accumulated 332.4 hours total flight time, of which 247.9 hours were listed as pilot-in-command. He had accumulated 290.6 hours and 40.6 hours in single engine airplanes and multi-engine airplanes, respectively. He had logged 166 hours of flight time in Cessna 152 airplanes. He had logged 2.1 hours in actual instrument meteorological conditions (IMC) and 58.6 hours as simulated IMC. He had provided 63.5 hours of flight instruction since receiving his initial flight instructor certificate on August 6, 2013. He had flown 13.2 hours during night conditions. According to the logbook, there was only one logged night flight during the 12 month period before the accident flight. The night flight was completed on November 15, 2013, and included 3 landings.

According to the flight instructor's logbook, he had flown 119.3 hours during the prior 12 months, 97.3 hours in the previous 6 months, 71.1 hours during prior 90 days, 65.7 hours in the previous 60 days, and 62.3 hours in the 30 day period before the accident flight. The flight instructor's logbook did not contain any recorded flight time for the 24 hour period before the accident flight; however, according to operator records, he had completed two earlier flights, totaling 2.5 hours, on the day of the accident.

--- Student Pilot ---

According FAA records, the student pilot, age 23, held a student pilot certificate. His last aviation medical examination was completed on July 1, 2013, when he was issued a first-class medical certificate with no limitations or restrictions. A search of FAA records showed no accident, incident, enforcement, or disciplinary actions.

The student pilot was a foreign-national who was receiving flight instruction toward a pilot certificate. According to available logbook information, between February 4, 2008, and September 18, 2008, the student pilot had received basic flight instruction in the Republic of India. During this period of flight instruction, the student pilot received 21.4 hours of dual flight instruction and flew 19.6 hours solo. After September 18, 2008, there were no logged flights until the student pilot completed his first instructional flight in the United States on October 18, 2013. The student pilot received an additional 12.5 hours of dual instruction and flew 0.3 hours solo while receiving flight instruction in the United States. The student pilot's combined flight experience totaled 53.8 hours, of which 19.9 hours were logged as solo flight. All of the student pilot's flight experience had been accumulated in Cessna 152 airplanes. According to available information, the student did not have any night flight experience before the accident flight. The student pilot's logbook contained a flight instructor endorsement for solo flight in a Cessna 152 that was dated November 9, 2013.

AIRCRAFT INFORMATION

The accident airplane was a 1981 Cessna model 152 single-engine airplane, serial number 15284692. A 110-horsepower Lycoming model O-235-L2C reciprocating engine, serial number L-17634-15, powered the airplane through a fixed-pitch, two blade, McCauley model 1A103/TCM6958 propeller. The airplane had a fixed tricycle landing gear, was capable of seating two individuals, and had a certified maximum gross weight of 1,675 pounds. The accident airplane was issued a standard airworthiness certificate on October 27, 1980. The current owner-of-record, WBR Interests LLC, purchased the airplane on February 20, 2007; however, the airplane had been operated by United Flight Systems since March 15, 1993.

The recording tachometer indicated 5,699.4 hours at the accident site. The airframe had accumulated a total service time of 15,699.4 hours at the time of the accident. The engine had accumulated a total service time of 5,610.4 hours at the time of the accident and 3,674.3 hours since a field overhaul that was completed on November 4, 2004. The last annual inspection of the airplane was completed on July 25, 2013, at 15,622.4 total airframe hours. On September 5, 2013, at 15,676.1 total airframe hours, the carburetor heat control cable was replaced. The last recorded maintenance was the replacement of the airplane's transponder on November 4, 2013. A postaccident review of the maintenance records found no history of unresolved airworthiness issues.

The airplane had a total fuel capacity of 26 gallons (24.5 gallons useable), which was distributed evenly between two 13-gallon wing fuel tanks. A review of fueling records established that the airplane fuel tanks were topped-off before the accident flight. Following the accident, a fuel sample was collected from the truck that was used to fuel the accident airplane. The fuel sample was blue in color, consistent with 100 low-lead aviation fuel. Additionally, the collected fuel sample did not contain any particulate or water contamination.

METEOROLOGICAL INFORMATION

At 1853, the DWH automated surface observing system reported: calm wind, visibility 10 miles, sky clear, temperature 23 degrees Celsius, dew point 21 degrees Celsius, and an altimeter setting of 29.89 inches-of-mercury. The United States Naval Observatory reported that the sunset and end of civil twilight at DWH was at 1725 and 1751, respectively. The moonrise was at 1742 for the full-phase moon.

The carburetor icing probability chart included in Federal Aviation Administration Special Airworthiness Information Bulletin No. CE-09-35, Carburetor Icing Prevention, indicated that the accident flight was likely operating in atmospheric conditions that were associated with a serious risk of carburetor ice accumulation while operating at reduced engine power settings.

COMMUNICATIONS

A review of available ATC information indicated that the accident flight had received normal air traffic control services and handling. A transcript of the voice communications recorded between the accident flight and David Wayne Hooks Air Traffic Control Tower are included with the docket materials associated with the investigation.

AIRPORT INFORMATION

The David Wayne Hooks Memorial Airport (DWH) is a privately owned airport that is open to the public. The airport is located approximately 17 miles northwest of Houston, Texas. The airport field elevation was 152 feet msl. The airport is serviced by an air traffic control tower and ground control. The airport has three parallel runways: runway 17R/35L (7,009 feet by 100 feet, asphalt); runway 17L/35R (3,987 feet by 35 feet, asphalt); and a water runway 17W/35W (2,530 feet by 100 feet).

Runway 17R incorporated a displaced threshold measuring 1,007 feet, a 4-light precision approach path indicator, runway end identifier lights, and high intensity runway edge lighting. According to air traffic control documentation, all runway lighting was functional at the time of the accident.

WRECKAGE AND IMPACT INFORMATION

A postaccident investigation confirmed that all airframe structural components and flight controls were located at the accident site. The wreckage was located on the east side of the airport, north of taxiway hotel and east of taxiway mike. The initial impact point was determined to be where the right wing collided with the northwest corner of a hangar structure. The outboard 9 feet of the right wing separated during the initial impact and was found about 90 feet northwest of the initial impact point on taxiway mike. The main wreckage, located about 29 feet north of the initial impact, consisted of the left wing, fuselage, empennage, engine, and propeller. The forward fuselage, including the cockpit, exhibited impact damage that significantly reduced the cabin volume. The left wing remained partially attached to the fuselage. The left wing had impacted a structural post and a spiral staircase that was associated with a residential hangar. The aircraft wreckage was orientated on a 035 degree magnetic heading. The fuselage was found resting on its lower surface. There was no evidence of an inflight or postimpact fire. The first responders reported that there was a substantial fuel odor at the accident site.

Flight control cable continuity could not be established due to multiple separations; however, all observed separations were consistent with overstress fractures. Both flaps had separated from their respective wings; however, a flap actuator measurement was consistent with the flaps being extended between 0 degrees and 10 degrees. The measured extension of the elevator trim actuator was consistent with a nose-level attitude. The ignition/magneto switch was found selected to the left magneto. The throttle was found extended about 1-inch from a full power position. The mixture control was found in the full-rich position. The carburetor heat control was found full forward in the OFF position. The carburetor air box had been crushed during the impact sequence, which precluded a determination if the carburetor heat had been activated at the time of the accident. Control cable continuity was confirmed between the carburetor heat box and the cockpit control. The cockpit fuel shutoff handle was found in the ON position and the firewall fuel strainer contained fuel. A fuel sample obtained from the fuel strainer exhibited no indication of water contamination when exposed to water detection paste. The fuel primer was found full forward and secured. The stall warning horn sounded when a vacuum was applied to the leading edge inlet.

The engine remained attached to the firewall by its mounts and control cables. Mechanical continuity was confirmed from the engine components to their respective cockpit controls. Internal engine and valve train continuity was confirmed as the engine crankshaft was rotated. Compression and suction were noted on all cylinders in conjunction with crankshaft rotation. The spark plugs were removed and exhibited features consistent with normal engine operation. Both magnetos provided spark on all leads when rotated by hand. All four engine cylinders were removed and no anomalies were noted with the cylinders, valves, pistons, connecting rods, or crankshaft. There were no obstructions between the air filter housing and the carburetor. The carburetor fuel bowl contained a liquid that was consistent with the color and odor of 100 low-lead aviation fuel. The fuel sample obtained from the carburetor bowl did not exhibit any water or particulate contamination. The Precision Airmotive model MA-3A carburetor, p/n 10-5199, s/n CR15409, was equipped with white, hollow, polymer floats (p/n 30-804). One of the two floats was found flooded with a blue fluid that was consistent with 100 low-lead aviation fuel. The second float was void of any fuel.

The propeller remained partially attached to the engine crankshaft flange. Both propeller blades exhibited minor leading edge damage. One propeller blade exhibited chordwise scratches. Neither blade exhibited appreciable spanwise bends or blade twist.

MEDICAL AND PATHOLOGICAL INFORMATION

On November 18, 2013, an autopsy was performed on the flight instructor by the Harris County Institute of Forensic Sciences, located in Houston, Texas. The cause of death was attributed to multiple blunt-force injuries that were sustained during the accident. The FAA's Civil Aerospace Medical Institute located in Oklahoma City, Oklahoma, performed toxicology tests on samples obtained during the autopsy. The toxicological test results were negative for carbon monoxide and ethanol. Atropine was detected in liver and blood samples. Atropine, often used in emergency resuscitation efforts, is a prescription anticholinergic agent and muscarinic antagonist.

On November 19, 2013, an autopsy was performed on the student pilot by the Harris County Institute of Forensic Sciences. The cause of death was attributed to multiple blunt-force injuries that were sustained during the accident. The FAA's Civil Aerospace Medical Institute performed toxicology tests on samples obtained during the autopsy. The toxicological test results were negative for carbon monoxide, ethanol, and all drugs and medications.

ADDITIONAL DATA/INFORMATION

On January 30, 2008, Precision Airmotive LLC, the manufacturer of the MA-3A carburetor, issued Mandatory Service Bulletin No. MSA-13 that required the replacement of brass and polymer hollow floats with a new solid-epoxy float design. According to the service bulletin, the installation of the new solid-epoxy float design would eliminate the known issues of hollow floats becoming flooded with fuel. Additionally, the service bulletin acknowledged that the polymer float design had known issues with fuel leaking into the hollow portion of the float through the welded seam. The service bulletin stated that a flooded float would reduce the buoyancy of the float, which could result in poor idle power performance and/or possible flooding of the carburetor. The service bulletin stipulated that affected carburetors be inspected within 30 days and then at 30 day intervals until the new solid-epoxy float was installed. The service bulletin stated that if the carburetor exhibited any signs of flooding, the float should be replaced immediately. Additionally, the service bulletin stipulated that all carburetors affected by the bulletin be overhauled every 10 years or at the specified engine time between overhaul (TBO), whichever occurred first.

On July 18, 2008, Lycoming Engines issued Mandatory Service Bulletin No. 582 that required all Lycoming engines that were equipped with Marvel-Schebler, Facet, Precision Airmotive, or Volare carburetors to be in compliance with Precision Airmotive Mandatory Service Bulletin No. MSA-13. The Lycoming service bulletin stipulated that affected carburetors be inspected within the next 30 days and then at 30 day intervals until the new solid-epoxy float was installed.

On February 1, 2009, Volare Carburetors LLC, who had acquired the Precision Airmotive carburetor line, issued Service Bulletin No. SB-2, which reiterated that hollow floats needed to be replaced with the newer solid-epoxy float design. The service bulletin stated that deteriorated, leaking, or broken floats can negatively affect engine performance. In conformance with the previously issued service bulletins, it stipulated that all affected carburetors be inspected within 30 days and then at 30 day intervals until the affected floats were replaced with the newer solid-epoxy float design.

On April 2, 2009, Volare Carburetors LLC issued Service Bulletin No. SB-5, which superseded the older Mandatory Service Bulletin No. MSA-13. The updated service bulletin clarified that the new float design was made of a solid, blue epoxy material. Previous service bulletins had mistakenly identified the new float design as being made from foam. Service Bulletin No. SB-5 stipulated that affected carburetor floats should be inspected per the guidance contained in Service Bulletin No. SB-2.

A review of maintenance records established that the carburetor was rebuilt and tested by Precision Airmotive on August 11, 2004, before being installed on the accident engine during a field overhaul completed on November 4, 2004. The engine overhaul documentation specified that the accident engine had a 2,400 hour TBO. At the time of the accident, the accident engine had accumulated 3,674.3 hours since its last overhaul. A review of available maintenance paperwork did not reveal any maintenance, repair, inspection, or overhaul of the carburetor since the last engine field overhaul. Additionally, the reviewed maintenance information did not contain any documentation that Service Bulletin Nos. MSA-13, 582, SB-2, or SB-5 had been complied with.

WBR INTERESTS LLC:   http://registry.faa.gov/N555UF

NTSB Identification: CEN14FA057 
 14 CFR Part 91: General Aviation
Accident occurred Sunday, November 17, 2013 in Spring, TX
Aircraft: CESSNA 152, registration: N555UF
Injuries: 2 Fatal.

This is preliminary information, subject to change, and may contain errors. Any errors in this report will be corrected when the final report has been completed. NTSB investigators either traveled in support of this investigation or conducted a significant amount of investigative work without any travel, and used data obtained from various sources to prepare this aircraft accident report.

On November 17, 2013, at 1915 central standard time, a Cessna model 152 airplane, N555UF, was substantially damaged during a forced landing at the David Wayne Hooks Memorial Airport (DWH), Spring, Texas. The flight instructor and student pilot were fatally injured. The airplane was registered to WBR Interests LLC and operated by United Flight Systems, under the provisions of 14 Code of Federal Regulations Part 91, without a flight plan. Night visual meteorological conditions prevailed for the local area training flight that had departed DWH at 1900.

According to preliminary air traffic control (ATC) data, the purpose of the instructional flight was to remain in the local traffic pattern to practice nighttime takeoffs and landings. At 1900:24, the tower controller cleared the accident flight for takeoff and to remain in a left traffic pattern for touch-and-go landings on runway 17R (7,009 feet by 100 feet, asphalt). The accident airplane was first observed on radar about 150 feet above ground level (agl) while on the upwind leg. The airplane continued to make left traffic for runway 17R before being cleared for the first touch-and-go landing at 1904:40. At 1906:48, the airplane descended below available radar coverage while on a 1/4 mile final for runway 17R. The airplane reemerged on radar at 1908:15, about 1/4 mile south of the runway departure threshold at about 250 feet agl. The airplane continued to make left traffic for runway 17R before being cleared for the second touch-and-go landing at 1911:10. At 1913:48, the last radar return was recorded for the accident flight about 1/3 mile north of the runway approach threshold at about 150 feet agl. At 1914:42, the flight instructor told the tower controller that they were having "engine problems" and requested to make a 180-degree turn back to the airport for a landing. (The airplane had completed the touch-and-go landing and was on initial climb when the flight instructor reported the loss of engine power.)

A witness reported hearing the accident airplane while it was on a left downwind leg for runway 17R and remarked that the sound of the engine was abnormal. The same witness reported that the engine continued to run rough while the airplane was on initial climb following a touch-and-go landing. Several witnesses to the accident reported seeing the accident airplane in a steep left turn before it entered a near vertical descent into terrain. Two of these witnesses reported seeing the wingtip navigation and strobe lights in a near vertical line (indicating a near 90-degree bank angle) before the airplane banked past 90-degrees and descended nose-low into the terrain.

At 1853, the DWH automated surface observing system reported: calm wind, visibility 10 miles, sky clear, temperature 23 degrees Celsius, dew point 21 degrees Celsius, and an altimeter setting of 29.89 inches-of-mercury. The United States Naval Observatory reported that the sunset and end of civil twilight at DWH was at 1725 and 1751, respectively. The moonrise was at 1742 for the full-phase moon.



Officials with the Harris County Medical Examiner’s Office have released the names of the two victims killed in Sunday evening’s fatal plane crash at David Wayne Hooks Memorial Airport.

Twenty-two year-old instructor Pedro Coronado, of Spring, and 23-year-old pilot Kartheek Balija were both killed in the accident, according to officials. According to HCN news partner KTRK-TV, investigators say the pilot reported engine trouble moments before the crash but the cause is currently unknown.

Federal Aviation Administration representative Lynn Lunsford said that the pilot was attempting to return to the runway when the plane crashed into the hangar at about 7:15 p.m, according to KTRK-TV’s report. Initial reports from the scene indicated that the plane crashed into a hanger and was fully engulfed in flames. Due to the heavy amount of fuel and fire, responders were unable to approach the wreckage.

Officials confirmed the plane, a single-engine Cessna 152, only had two occupants on board. One victim died at the scene and one was transported by ground to Memorial Hermann Hospital. According to KTRK-TV, medical examiners identified the two on board as a student and an instructor.

Representatives from the airport and nearby flight school could not be reached for comment.

The National Transportation Safety Board is currently leading the investigation, Lunsford said.


 



 








 

HOUSTON (KTRK) -- A plane crashed Sunday night at an airport in Spring, killing two people aboard, and experts want to know what went wrong. 

Dozens of firefighters rushed to David Wayne Hooks Memorial Airport on Boudreaux Road in northwest Harris County as alerts about the plane crash rang out around 7:15pm.

According to the Federal Aviation Administration, the pilot of the single-engine Cessna 152 had been in the traffic pattern performing touch-and-go landings when engine problems were reported.

We're told the pilot was returning to the runway when the plane clipped one hangar, then crashed into another hangar.

Harris County Sheriff's Office authorities said the it took a moment before emergency crews could safely approach the wreckage due to the large amount of fuel that spilled.

Witnesses reported seeing the plane out of control just before the crash happened.

Rob Patterson, who works near the airport, said, "It was towards the end of the day. They said the plane was going straight up and it started going straight up in the air. And it looked like it got inverted and then it came down. Turn around to land and then came straight down on the side of the runway."

One person in the plane died at the scene. Another was rushed to Memorial Hermann Hospital in critical condition, but later died. The crash victims have not yet been identified.

The National Transportation Safety Board is now responsible for this investigation. So far we have only been told an investigator will be assessing the wreckage and determining what potentially caused the engine to fail.


Source:  http://abclocal.go.com

 HOUSTON (KTRK) -- A plane crashed Sunday night at an airport in Spring, killing two people aboard, and experts want to know what went wrong.

Investigators say the pilot of that plane reported engine trouble moments before the crash. They're still, however, trying to figure out why.

As National Transportation Safety Board investigators work to determine what caused the crash, we were able to get a closer look at the wreckage in the daylight. According to the FAA, the single engine Cessna 152 came down Sunday at about 7:15pm. FAA spokesperson Lynn Lunsford says the pilot was trying to return to the runway when the plane crashed into the hangar.

Rob Patterson, who spoke with eyewitnesses, said, "It started going straight up in the air. It looked like it got inverted and then came down."

Patterson knows people who witnessed the aircraft's final moments. He says they couldn't believe what they were seeing.

"It turned around, it looked like to land and it just came straight down," he said.

The tail number on that plane N55UF matches that on the website of nearby United Flight Systems. They run a flight school at Hooks Airport. The medical examiner identifies the two on board that plane as a pilot and an instructor.

At United on Monday we found a sign on the door reading "closed until further notice." No one from the flight school returned our repeated calls.

Authorities have not yet publicly identified the two who died in the crash.


http://abclocal.go.com

HARRIS COUNTY – A flight instructor and a student pilot  were killed after their small plane crashed into a building at Hooks Airport Sunday evening in northwest Harris County, officials confirmed. 

 It happened at the airport located at 8830 Boudreaux Road around 7:15 p.m.

According to the Harris County Sheriff’s Office, the two were performing touch and go maneuvers in the Cessna 152 when the pilot called the tower to report engine trouble. The plane then slammed into a hangar and burst into flames.

First responders were not able to get close to the wreckage because of the blaze. Once they were able to get to the victims, the injuries were too severe.

The student was pronounced dead at the scene and the instructor was taken by ambulance to Memorial Hermann Hospital, but also died.

The plane is registered to an insurance company in New Castle, Delaware.


Source:   http://www.khou.com

No comments:

Post a Comment