Tuesday, May 24, 2016

Cessna 501 Citation I/SP, N804ST, registered to and operated by Eagle II Aero LLC: Accident occurred May 23, 2016 near Texarkana Regional Airport-Webb Field (KTXK), Miller County, Arkansas

The National Transportation Safety Board did not travel to the scene of this accident.

Additional Participating Entity:
Federal Aviation Administration / Flight Standards District Office; Little Rock, Arkansas

Aviation Accident Factual Report - National Transportation Safety Board: https://app.ntsb.gov/pdf

Investigation Docket - National Transportation Safety Board: https://dms.ntsb.gov/pubdms

Eagle II Aero LLC: http://registry.faa.gov/N804ST

Location: Texarkana, AR
Accident Number: CEN16LA197
Date & Time: 05/23/2016, 2156 CDT
Registration: N804ST
Aircraft: CESSNA 501
Aircraft Damage: Substantial
Defining Event: Pressure/environ sys malf/fail
Injuries: 3 Minor, 1 None
Flight Conducted Under: Part 91: General Aviation - Executive/Corporate 

On May 23, 2016, about 2156 central daylight time, a Cessna 501, N804ST, lost cabin pressurization during cruise at flight level (FL) 430 and entered an uncontrolled descent near Texarkana, Arkansas. The pilot regained consciousness and control of the airplane. The pilot landed the airplane without further incident at Texarkana Regional Airport-Webb Field (TXK), Texarkana, Arkansas. The airplane sustained substantial damage to both wings due to the excessive aerodynamic loads on the wings during the descent/recovery. The airline transport pilot and two passengers sustained minor injuries and one passenger was uninjured. The airplane was registered to and operated by Eagle II Aero LLC under 14 Code of Federal Regulations Part 91 as an executive/corporate flight that was operating on an instrument flight rules (IFR) flight plan. Night meteorological conditions prevailed at the time of the accident. The flight last departed from Perryville Municipal Airport, Perryville, Missouri (K02), about 2056, and was destined to San Antonio International Airport (SAT), San Antonio, Texas.

The airplane was flown by a single-pilot for the accident flight. According to air traffic control (ATC) radio communications, N804ST made initial contact with Memphis Center at 2056, after departing K02, to report climbing through 9,200 feet with an IFR flight plan on file. N804ST responded to all ATC transmissions while climbing to and leveling off at flight level 430, which was an altitude that was above reported cloud tops at FL 390. At 2154, Fort Worth Center called N804ST, but there was no response from N804ST. At 2155, Fort Worth Center attempted to contact N804ST three times and issued the Fort Smith altimeter. Fort Worth Center contacted Memphis Center and advised that N804ST had an "issue" and was descending. At 2156, Memphis Center instructed American Airlines flight 93 (AAL93) to attempt to contact N804ST on guard frequency. Fort Worth Center asked N804ST to IDENT; N804ST reported an explosive decompression. Fort Worth Center advised Memphis Center that they were now communicating with N804ST. At 2157, AAL93 advised Memphis Center that they were unable to contact N804ST on guard frequency. N804ST reported that the airplane was under control and would level off shortly. Fort Worth Center asked whether N804ST would like to fly to TKX or Fort Smith Regional Airport (FSM), Fort Smith, Arkansas. At 2148, the pilot of N804ST asked for a few minutes to "figure this out" and then advised he would like to land at TKX. Memphis Center advised that N804ST was located 12 o'clock and 35 miles from TKX. The pilot performed a visual approach and landing to runway 13 (5,200 by 100 feet, asphalt) at TXK, where the flight landed without further incident.

The pilot reported in a written statement that within 20 seconds, the airplane lost all cabin pressurization, and the cabin altitude climbed from 8,000 feet and 8.5 psi differential (psid) to ambient altitude and 0 psid. All the occupants lost consciousness. The pilot regained consciousness and control of the airplane at 7,000 feet.

According to the Federal Aviation Administration (FAA) coordinator for the accident, the pilot stated that he was not wearing an airplane supplemental oxygen system crew mask during the flight.

Pilot Information

Certificate: Airline Transport; Commercial
Age: 58, Male
Airplane Rating(s): Multi-engine Land; Single-engine Land; Single-engine Sea
Seat Occupied: Left
Other Aircraft Rating(s): Glider; Helicopter
Restraint Used: Lap Only
Instrument Rating(s): Airplane; Helicopter
Second Pilot Present: No
Instructor Rating(s): Airplane Multi-engine; Airplane Single-engine; Glider
Toxicology Performed: No
Medical Certification: Class 2 Without Waivers/Limitations
Last FAA Medical Exam: 08/22/2015
Occupational Pilot: No
Last Flight Review or Equivalent: 05/11/2016
Flight Time:  15000 hours (Total, all aircraft), 5000 hours (Total, this make and model), 14800 hours (Pilot In Command, all aircraft), 50 hours (Last 90 days, all aircraft), 20 hours (Last 30 days, all aircraft), 2 hours (Last 24 hours, all aircraft) 

The pilot held an airline transport pilot certificate with the following type ratings: CE-500, CE-525, CE-650, MJ-300, BE-400, G-1159, DC-3, N-P51N, N-T28, T-33. On November 15, 2014, the pilot completed single-pilot exemption training including differences training for CE-500, CE-550, and CE-560 training. The pilot's last flight review was dated May 11, 2016, using a Beechcraft BE400. The pilot reported a total flight time of 15,000 hours, of which 5,000 hours were in the make and mode of the accident airplane.

Aircraft and Owner/Operator Information

Aircraft Manufacturer: CESSNA
Registration: N804ST
Model/Series: 501
Aircraft Category: Airplane
Year of Manufacture: 1980
Amateur Built: No
Airworthiness Certificate: Normal
Serial Number: 501-0146
Landing Gear Type: Retractable - Tricycle
Seats: 8
Date/Type of Last Inspection: 04/15/2016, Continuous Airworthiness
Certified Max Gross Wt.: 12500 lbs
Time Since Last Inspection:
Engines: 2 Turbo Fan
Airframe Total Time: 7424.8 Hours as of last inspection
Engine Manufacturer: Williams International Company
ELT: Installed, not activated
Engine Model/Series: FJ44-2A
Registered Owner: EAGLE II AERO LLC
Rated Power: 2300 lbs
Operator: EAGLE II AERO LLC
Operating Certificate(s) Held: None 

The airplane's type certificate, held by Textron Aviation Inc., shows that the Cessna 501 was certified under Part 23 with two Pratt & Whitney Aircraft of Canada, Ltd. JT15D-1A or JT15D-1B turbofan engines and had a maximum operating altitude of 41,000 feet.

The accident airplane was modified from its type design by supplemental type certificates (STCs), held by Sierra Industries Ltd., which increased the maximum operating altitude to 43,000 feet. The two STCs were:

SA732NW was for the installation of the Eagle SP performance system, including recontoured wing leading edge, wing tip extension, increased gross weight, increased fuel capacity, and other minor refinements.

ST09559AC was for the installation of Williams International Company. L.L.C. FJ44-2A engines in Cessna 501/500 aircraft or Williams International Company, L.L.C. FJ44-3A engines in Cessna Model 550/S550 aircraft. This STC increased the maximum operating altitude to 43,000 feet.

The Model 500 Maintenance Manual (Rev 39), Floor Panels – Inspection/Check called for the inspection of the air conditioning system in section D. Inspect Air Conditioning System: (1) Inspect all duct work and tubing for security of installation, evidence of damage or leakage, and (3) Inspect flapper check valves at air mixer assembly for ease of operation or evidence of binding.

The most recent maintenance inspection of the airplane was a Phase 5 inspection. A copy of the maintenance checklist used for the inspection, Model 500 Maintenance Manual (Rev 37) had the following entries: "Date:" - no entry made, "Registration Number: N804ST", "Serial Number: 501-0146", and "Total Time: 7424.8".

A Sierra Industries Ltd. Maintenance Transaction Report, dated April 15, 2016, stated, "Completed phase inspections in accordance with Cessna 500 maintenance manual chapter 5," at 7,424.8 aircraft hours, 6,411 landings, and no. 1 engine and no. 2 engine total hours were 846.8 hours and 539 cycles.

The Hobbs meter following the accident indicated 0411.3 hours.

The airplane oxygen system supplies breathing oxygen to the crew at all times and to the passengers when required. The pilot can manually drop the passenger masks by selecting manual drop on the oxygen control valve, or the passenger masks will automatically drop at 14,800 ±200 feet cabin altitude. The pilot can select crew only which will shutoff flow to the passengers. 

Meteorological Information and Flight Plan

Conditions at Accident Site: Visual Conditions
Condition of Light: Night/Dark
Observation Facility, Elevation: TXK
Observation Time: 2153 CDT
Distance from Accident Site:
Direction from Accident Site:
Lowest Cloud Condition: Scattered / 9500 ft agl
Temperature/Dew Point: 23°C / 18°C
Lowest Ceiling: None
Visibility:  10 Miles
Wind Speed/Gusts, Direction: 4 knots, 120°
Visibility (RVR):
Altimeter Setting: 29.94 inches Hg
Visibility (RVV):
Precipitation and Obscuration: No Obscuration; No Precipitation
Departure Point: Perryville, MO (K02)
Type of Flight Plan Filed: IFR
Destination: San Antonio, TX (SAT)
Type of Clearance: IFR
Departure Time: 2056 CDT
Type of Airspace: 

Wreckage and Impact Information

Crew Injuries: 1 Minor
Aircraft Damage: Substantial
Passenger Injuries: 2 Minor, 1 None
Aircraft Fire: None
Ground Injuries: N/A
Aircraft Explosion: None
Total Injuries: 3 Minor, 1 None
Latitude, Longitude: 33.441667, -94.037778 (est) 

Post-accident examination of the airplane by the FAA coordinator revealed that the cockpit supplemental oxygen supply gauge indicated about 17 "psi x100," which was in the gauge's green arc of 16-18 psi x100.

The cockpit supplemental oxygen system switch was in the "Normal" position (which would have provided oxygen to the cabin masks). The cabin oxygen masks were not deployed. The pilot stated to the FAA coordinator that the switch was in the "Crew" position, and he did not know how or why it was in the "Normal" position. The pilot later told the FAA coordinator that he changed the oxygen switch position after the accident.

The examination revealed that the aft pressure bulkhead check valve flapper had half of its non-metallic flapper fractured into several pieces, which were resting on the fuselage floor. The second half of the check valve flapper was intact in valve body. The air conditioning system's primary pressurization duct leading to the cabin was separated from its connection with the water separator. The duct's metal worm-gear retaining clamp was resting around the duct and away from its attachment point to the separator. The clamp's retaining screw was in place. The clamp was not fractured. The clamp, the check valve, and the flapper pieces were sent to the National Transportation Safety Board Material Laboratory for examination. 

Tests And Research

Materials Laboratory Examination of Check Valve and Hose Clamp

The examination labeled the check valve flapper half pieces recovered from the fuselage floor as flapper 1, and the flapper that was intact in the valve body as flapper 2. Both flappers were fabricated from glass-filled polybutylene terephthalate (PBT). Based on the presence of an injection gate and ejection pin marks, the flappers were fabricated by injection molding. Based on unique artifacts molded into the surfaces of the flappers, both flappers were molded from the same mold cavity. Both flappers had the following number molded onto the downstream side surface, DSP 904-0012-3, and did not exhibit any other identifying marks such as a date code or mold cavity number.

Flapper 1 exhibited radially-oriented cracks originating within its approximate center; two of the primary cracks were nearly bilaterally symmetric in shape consistent with possible flow patterns and knitting in the part from the mold filling process. In all instances, the cracks initiated on the downstream side and propagated through the thickness towards the upstream side—driven primarily by bending stresses on the flapper.

One fragment from flapper 1 was selected for deeper examination, which showed the presence of networks of fine cracks (also known as surface checks, surface crazing, or craze cracks). A fine network of cracks was present adjacent to the main fracture surface. The primary fracture surface of the polymeric resin phase was smooth and glassy with hackle marks indicative of though-thickness crack propagation from the downstream side to the upstream side. The fracture surface exhibited yellow discoloration in areas along its length indicating that portions were pre-existing. Scanning electron microscope examination also revealed a fine network of secondary cracks along the second primary fracture.

The hinge fragments for flapper 1 exhibited cracks that progressed radially outward from the inside surface to the outside surface. The fracture surfaces on two of the hinge cracks exhibited yellow discoloring, consistent with progressive crack development with time (slow crack growth).

Flapper 2 exhibited a primary crack on the downstream side. A portion of one of the flapper hinges was also missing. Stereo-zoom microscopic evaluation indicated that a portion of one of the hinges fractured due to the development of a crack that initiated at the inner surface and propagated to the external surface. One of the fractures exhibited yellow discoloring, consistent with progressive crack development with time (slow crack growth).

The inside surface length of the hose clamp is about 11.1 inch and corresponds to an approximately 3.5 inch diameter. The hose clamp design is consistent with a worm gear style with a safety collared screw and perforated band manufactured by C. McGunnigle Co. Inc. Kenilworth, NJ, under the Breeze Aero Seal ® trademark. The clamp is consistent with an SAE J1508 Type F size 48 (2 9/16 to 3 1/2 diameter size range). 

Additional Information

Part 91 Regulations on the Use of Supplemental Oxygen

Part 91.211 Supplemental oxygen.

(a)General. No person may operate a civil aircraft of U.S. registry –

(b) Pressurized cabin aircraft.

(1) No person may operate a civil aircraft of U.S. registry with a pressurized cabin -

(i) At flight altitudes above FL 250 unless at least a 10-minute supply of supplemental oxygen, in addition to any oxygen required to satisfy paragraph (a) of this section, is available for each occupant of the aircraft for use in the event that a descent is necessitated by loss of cabin pressurization; and

(ii) At flight altitudes above FL 350 unless one pilot at the controls of the airplane is wearing and using an oxygen mask that is secured and sealed and that either supplies oxygen at all times or automatically supplies oxygen whenever the cabin pressure altitude of the airplane exceeds 14,000 feet mean sea level, except that the one pilot need not wear and use an oxygen mask while at or below FL 410 if there are two pilots at the controls and each pilot has a quick-donning type of oxygen mask that can be placed on the face with one hand from the ready position within 5 seconds, supplying oxygen and properly secured and sealed. 

NTSB Identification: CEN16LA197
14 CFR Part 91: General Aviation
Accident occurred Monday, May 23, 2016 in Texarkana, AR
Aircraft: CESSNA 501, registration: N804ST
Injuries: 1 Uninjured.

This is preliminary information, subject to change, and may contain errors. Any errors in this report will be corrected when the final report has been completed. NTSB investigators may not have traveled in support of this investigation and used data provided by various sources to prepare this aircraft accident report.

On May 23, 2016, about 2252, a Cessna 501, N804ST, lost cabin pressurization during cruise at flight level 430 and entered an uncontrolled descent near Texarkana, Arkansas. The pilot regained consciousness and control of the airplane about 7,000 feet mean sea level and landing without further incident. The airplane sustained substantial damage to both wings due to the excessive loads on the wings during the descent/recovery. The airline transport pilot, who was the sole occupant, was uninjured. The airplane was registered to Eagle II Aero LLC and was operated under 14 Code of Federal Regulations as a personal flight that was operating on an instrument rules flight plan. Night meteorological conditions prevailed at the time of the accident. The flight last departed from Perryville Municipal Airport, Perryville, Missouri (K02) and was destined to San Antonio International Airport (SAT), San Antonio, Texas.

Post-accident examination of the airplane revealed that the primary pressurization duct into the cabin was separated from its connection to the water separator. The duct's metal retaining clamp was present with its retaining screw in place. The clamp was not fractured and was resting around the metal duct leading to the separator.

No comments:

Post a Comment