Tuesday, August 1, 2017

Grumman American AA-1B Trainer, N6216L: Accident occurred August 01, 2017 near Deer Valley Airport (KDVT), Phoenix, Maricopa County, Arizona

The National Transportation Safety Board did not travel to the scene of this accident.

Additional Participating Entities:

Federal Aviation Administration / Flight Standards District Office; Scottsdale, Arizona
Lycoming Engines; Williamsport, Pennsylvania
Superior Air Parts; Coppell, Texas

Aviation Accident Factual Report - National Transportation Safety Board: https://app.ntsb.gov/pdf

Investigation Docket - National Transportation Safety Board: https://dms.ntsb.gov/pubdms 
 
http://registry.faa.gov/N6216L


Location: Phoenix, AZ
Accident Number: WPR17LA175
Date & Time: 08/01/2017, 1300 MST
Registration: N6216L
Aircraft: GRUMMAN AA1
Aircraft Damage: Substantial
Defining Event: Loss of engine power (partial)
Injuries: 2 Serious
Flight Conducted Under: Part 91: General Aviation - Personal 

On August 1, 2017, about 1300 mountain standard time, an American AA-1B airplane, N6216L, was substantially damaged following a partial loss of engine power and subsequent loss of control during takeoff initial climb at the Deer Valley Airport (DVT), Phoenix, Arizona. The private pilot and pilot rated passenger were seriously injured. The airplane was registered to a private individual and operated by the pilot under the provisions of Title 14 Code of Federal Regulations Part 91. Visual meteorological conditions prevailed at the time of the accident and no flight plan was filed. The planned local flight was originating at the time of the accident.

The pilot was not able to recall the events leading up to the accident due to his injuries.

The passenger reported that shortly after takeoff, and while turning crosswind to the north, the engine experienced a total loss of power. The passenger stated that at this time the pilot attempted to restart the engine but was unsuccessful. He then attempted to make a left 180° turn back to the airport, however, was unsuccessful as the airplane stalled and crashed into a fence and a tree. The passenger mentioned that at the time of the accident, the engine was completely off; "there was no power at all to the engine."

A witness to the accident, who was a student pilot at the time, reported that he was observing a small Grumman [airplane] take off from runway 25L at DVT. The witness stated that the airplane climbed to an altitude of about 200 to 300 ft above ground level, when he heard the engine slow to what sounded like half power. He further stated that a few seconds later the airplane leveled off and it veered about 30° to the right, and then began a steep 45° or more bank to the left. The witness opined that it appeared that the pilot was going to try to make it back to runway 7R, or at least land in the field near the end of the runway. However, during the left turn on an approximately southwest heading, the witness stated that the airplane stalled and banked sharply "…like a snap roll to the right and pitched nose down"; he did not witness the last few feet prior to impact.

According to the Federal Aviation Administration (FAA) inspector who responded to the accident site, several witnesses reported that after the airplane had taken off and was in its initial climb to the west, the wings started to rock back and forth. The airplane subsequently began to descend, struck the airport's western perimeter fence, and collided with a tree where it came to rest. Both wings and the engine had separated from the airplane due to impact forces.

An acquaintance of the pilot, a certificated flight instructor (CFI), reported that a few days prior to the accident the pilot contacted him and reported that on a recent flight the airplane's engine had run a bit rough for about 3 to 5 seconds. He asked the pilot what actions he took, and the pilot stated that he switched the electric boost pump on and switched fuel tanks, which resulted in the engine running smoothly. The CFI stated that he thought the pilot mentioned that he then switched the fuel selector back to the rough running side and it again ran smoothly but was not sure. The pilot did not indicate which side or tank had the issue. The CFI did not know if the pilot had a mechanic examine the engine prior to the accident flight, which occurred about 4 to 6 days after the rough running engine was reported to him. The CFI informed the airplane's owner of his conversation with the pilot relative to the engine issue when he met him at the hospital on the day of the accident. The CFI opined that the owner had no knowledge of the rough running engine issue, that he had taken all precautions to ensure that the airplane was safe, and that he had just spent $5,000 on an annual inspection.

During the investigation the passenger reported to the NTSB IIC that a few days prior to the accident the pilot was telling people and the CFI that he was having trouble with the fuel selector. When the IIC queried the CFI about the passenger's statement, the CFI stated that the pilot never mentioned anything about the fuel selector being an issue during any of their conversations.

Pilot Information

Certificate: Private
Age: 18, Male
Airplane Rating(s): Single-engine Land
Seat Occupied: Left
Other Aircraft Rating(s): None
Restraint Used: 3-point
Instrument Rating(s): None
Second Pilot Present: No
Instructor Rating(s): None
Toxicology Performed: No
Medical Certification: Class 1 Without Waivers/Limitations
Last FAA Medical Exam: 04/23/2015
Occupational Pilot: No
Last Flight Review or Equivalent:
Flight Time:  270 hours (Total, all aircraft), 226 hours (Total, this make and model), 207 hours (Pilot In Command, all aircraft), 85 hours (Last 90 days, all aircraft), 33 hours (Last 30 days, all aircraft), 2 hours (Last 24 hours, all aircraft)

The 18-year-old pilot held a private pilot certificate with a rating for airplane single-engine land. A friend of the pilot reported that the pilot had accumulated about 270 total flight hours, 207 hours as pilot-in-command, and 226 hours which were in the same make and model as the accident airplane. The pilot held an FAA first-class airman medical certificate, which was issued on April 23, 2015, with no limitations reported. 

Aircraft and Owner/Operator Information

Aircraft Make: GRUMMAN
Registration: N6216L
Model/Series: AA1 B
Aircraft Category: Airplane
Year of Manufacture: 1972
Amateur Built: No
Airworthiness Certificate: Normal
Serial Number: AA1B-0016
Landing Gear Type: Tricycle
Seats: 2
Date/Type of Last Inspection: 05/11/2017, 100 Hour
Certified Max Gross Wt.: 1600 lbs
Time Since Last Inspection: 125 Hours
Engines: 1 Reciprocating
Airframe Total Time: 4196 Hours as of last inspection
Engine Manufacturer: Lycoming
ELT: C91  installed, not activated
Engine Model/Series: O320 A3A
Registered Owner: Robert L Swortzel
Rated Power: 150 hp
Operator: On file
Operating Certificate(s) Held: None 

The two-seat, low-wing airplane, serial number AA1B-0016, was manufactured in 1972. It was powered by a Lycoming model O-320-A3A, 150-horsepower engine, and equipped with a Sensinich two-blade propeller, model M74DM-0-58. A review of the maintenance logbook records revealed that during the 100-hour inspection that was performed on February 9, 2017, the number 3-cylinder was replaced with a new Millennium cylinder, part number SA 32006N-A21P, at a tach time of 432.4 hours. At the time of the inspection when the number 3-cylinder was checked for compression, it registered 36/80, which prompted the cylinder change. The most recent 100-hour inspection was performed on May 11, 2017, about 125 hours prior to the accident. At this time the number 3-cylinder exhaust gasket was replaced. In conjunction with the inspection, a subsequent ground run revealed no anomalies with the engine. A maintenance logbook entry revealed that all cylinders were inspected with a borescope. At the time of the accident the cylinder had accumulated 324.1 hours of operation since installation. (Refer to excerpts of maintenance records, which are appended to the docket for this accident.)

The airframe and powerplant mechanic who performed the installation of the number 3-cylinder during a 100-hour inspection, stated that on July 29, 2017, three days prior to the accident, he and the accident pilot exchanged a series of text messages, in which the pilot stated that on a go-around/missed approach, the engine started shaking and shuttered for about 10 seconds, and then it was fine. When the mechanic replied that he wondered if it could have been carburetor ice, the pilot said he didn't think so. The mechanic also mentioned that he did not perform any work on the airplane after the initial report of the engine running rough.

Meteorological Information and Flight Plan

Conditions at Accident Site: Visual Conditions
Condition of Light: Day
Observation Facility, Elevation: DVT, 1478 ft msl
Distance from Accident Site: 1 Nautical Miles
Observation Time: 1253 MST
Direction from Accident Site: 270°
Lowest Cloud Condition: Clear
Visibility:  10 Miles
Lowest Ceiling: None
Visibility (RVR):
Wind Speed/Gusts: 4 knots /
Turbulence Type Forecast/Actual: None / None
Wind Direction: 180°
Turbulence Severity Forecast/Actual: N/A / N/A
Altimeter Setting: 29.93 inches Hg
Temperature/Dew Point: 34°C / 16°C
Precipitation and Obscuration: No Obscuration; No Precipitation
Departure Point: Phoenix, AZ (DVT)
Type of Flight Plan Filed: None
Destination: Sedona, AZ (SEZ)
Type of Clearance: None
Departure Time: 1300 MST
Type of Airspace: Class D

At 1253, the DVT weather reporting facility indicated wind from 180° at 4 knots, visibility 10 miles, sky clear, temperature 34° Celsius (C), dew point 16° C, and an altimeter setting of 29.93 inches of mercury.

Airport Information

Airport: Phoenix Deer Valley (DVT)
Runway Surface Type: Asphalt
Airport Elevation: 1478 ft
Runway Surface Condition: Dry
Runway Used: 25L
IFR Approach: None
Runway Length/Width: 8196 ft / 100 ft
VFR Approach/Landing: Forced Landing 

The airport is surrounded on the south, west and north by industrial and commercial buildings. The road which borders the airport on its west perimeter is a main north/south arterial road, as is the road which borders the south side of the airport, both of which have traffic throughout the day. The nearest open field is located about 1,500 ft northeast of the initial upwind departure leg.

Wreckage and Impact Information

Crew Injuries: 1 Serious
Aircraft Damage: Substantial
Passenger Injuries: 1 Serious
Aircraft Fire: None
Ground Injuries: N/A
Aircraft Explosion: None
Total Injuries: 2 Serious
Latitude, Longitude: 33.686667, -112.099722 (est) 

A FAA aviation safety inspector, who responded to the accident site shortly after the accident, reported that after impacting the ground the airplane skidded into a tree, then broke at mid-fuselage splitting the airplane body into two pieces, with the cockpit and the fuselage on each side of the tree. The inspector stated that the engine appeared to be producing power, based on observable propeller blade signatures. The blades exhibited chordwise striations across the cambered surface, torsional twisting and trailing edge "S" bending. Additionally, the engine had separated from the airplane and came to rest on the road that borders the airport to the west, about 90 ft south of the main wreckage site. Both the left and right wings had also separated from the fuselage, with the left wing having come to rest about 30 ft northwest of the main wreckage, and the right wing about 180 ft south of the main wreckage site.

During a postaccident examination of the fuel selector by the NTSB IIC and a Federal Aviation Administration inspector, the component functioned as designed through all positions. It was observed that a stop pin was sheared off inside of the selector that would have prevented the selector from traveling too far to the left. Photo documentation at the accident site showed that the fuel selector was selected to the left tank position.

The left fuel tank had been breached and showed evidence of fuel dispersion; the quantity of the fuel spill was estimated to be between 3 to 5 gallons. The inspector reported that the right wing did not show any evidence of a fuel spill and that no fuel remained in the wing.

The inspector opined that the Type Certificate Data Sheet for the AA-1B airplane states that there is 2 gallons of unusable fuel in each wing. The inspector's review of the fuel receipts for the accident airplane revealed that 7.8 gallons of fuel was purchased on July 31 at 2107, and that the accident flight was the first flight since the fuel was added.

Engine Examination

The engine remained attached to the engine mount and had been liberated from the firewall during the accident/impact sequence. The engine had sustained significant impact energy absorption to the right forward/lower area of the number two cylinder and exhaust system. The attached propeller and flywheel were bent. All engine accessories remained secure at their respective mountings. Visual examination of the engine revealed no external evidence of pre-impact catastrophic mechanical malfunction or fire.

The left and right magnetos remained securely clamped at their respective mounting pads. The ignition harness was secure at each magneto. Magneto to engine timing could not be ascertained, due to the flywheel impingement on the engine crankcase. The magnetos were removed for examination. Each magneto produced spark at the end of the respective spark plug lead, during hand rotation of the drive. The drives of each magneto remained intact and undamaged.

The propeller and flywheel were removed to facilitate the examination. The top spark plugs were removed, examined and photographed. The rocker covers of each cylinder were removed. The vacuum pump was removed, and the crankshaft was rotated by hand through the drive pad utilizing a drive tool. The crankshaft was free and easy to rotate in both directions. "Thumb" compression was observed in proper order on cylinders 1, 2 and 4. It was noted that the number 3-cylinder exhaust valve was not moving and stuck in the OPEN position. The complete valve train was observed to operate in proper order and appeared to be free of any pre-mishap mechanical malfunction. Normal "lift action" was observed at each rocker assembly and pushrod of the number 3 exhaust valve. Clean, uncontaminated oil was observed at all four rockerbox areas. Mechanical continuity was established throughout the rotating group, valve train and accessory section during hand rotation of the crankshaft. The bottom spark plugs were removed, examined and photographed. The spark plug electrodes remained mechanically undamaged, and according to the Champion Spark Plugs "Check-A-Plug" chart AV-27, the spark plug electrodes displayed coloration consistent with normal operation. The combustion chamber of each cylinder was examined through the spark plug holes utilizing a lighted borescope. The combustion chambers remained mechanically undamaged, and there was no evidence of foreign object ingestion or detonation. The valves were intact and undamaged. There was no evidence of valve to piston face contact observed. The gas path and combustion signatures observed at the spark plugs, combustion chambers and exhaust system components displayed coloration consistent with normal operation. There was no oil residue observed in the exhaust system gas path. The exhaust system was found free of obstructions.

The number 3-cylinder was removed to facilitate further examination. The cylinder assembly was properly secured to the crankcase and appeared free of significant impact energy damage. The intake, exhaust rockers and valve train components within the rockerbox area appeared properly lubricated and free of mechanical damage. The intake and exhaust pushrods remained straight and free of damage. The intake pushrod shroud had sustained superficial impact damage. The intake rocker assembly remained undamaged and exhibited no evidence of lubrication depravation. There was no intake rocker pin oil hole. The exhaust rocker assembly remained undamaged and exhibited no evidence of lubrication depravation. The exhaust rocker pin oil hole remained free of obstruction.

The number 3-piston was removed from the connecting rod. The piston pin was undamaged and free of heat distress. The piston pin bushing remained secure and exhibited no unusual wear signatures. The number 3-piston exhibited no evidence of valve to piston face contact. The piston skirt exhibited no unusual wear signatures. The ring assemblies at each piston were intact and free to rotate within their respective ring land. The cylinder barrel bore remained free of damage and was absent of any significant heat distress signatures. There was no evidence of foreign object ingestion or detonation. The valves remained intact and undamaged. There was no further disassembly or examination of the subject cylinder. The valve was not moved from the original position it was found in during this examination.

Tests And Research

An examination of the number 3-cylinder was performed at the facilities of Superior Air Parts, Coppell, Texas. The results of the examination revealed the following:

There were no valve strike marks or impact damage exhibited on the piston. The piston rings were free in the ring lands and there was no damage to the sides of the piston. There was no evidence of scuffing, scoring or overheating. The piston part number could not be observed on the top due to heavy combustion deposits. Piston overall height was measured to be 3.177", which included the build-up of carbon deposits on top. The measurement was consistent with a low compression piston correct for the engine model. The piston pin was removed easily to facilitate inspection of the back side of the piston. The forging number on the underside of the piston was 13020, and manufactured by ECI. With the exception of heavy combustion deposits, the piston exhibited normal operational signatures.

The intake and exhaust valves exhibited combustion deposits on the stems close to the rear of the valve face. The exhaust valve was found stuck in the open position with the valve spring nearly depressed fully. The valve was tapped on the combustion side with a rubber mallet to close the valve to facilitate removal of the valve keepers and removal of the valve for inspection. With the valve keepers removed, the intake valve was removed with little effort. The exhaust valve required tapping with a rubber mallet and brass drift to remove it from the valve guide. The valve was tested using a Rockwell hardness tester and found to be within specifications.

The exhaust valve stem and guide exhibited heavy combustion deposits. The valve guide diameters were measured with the deposits present. The deposits were then removed using a .4995" ream in accordance with Lycoming Service Instruction 1425A, titled "Suggested Maintenance Procedures to Reduce the Possibility of Valve Sticking." The guides were re-measured after reaming and found to have an average of .0017" build-up of combustion deposits. The deposits were collected into a filter and sealed with the cylinder. All material removed during reaming was combustion deposits and no metallic material was found. (For additional information relative to the before and after ream dimensions, refer to the Summary Airframe and Engine Examination report, which is appended to the docket for this accident.)

The NTSB investigator who observed the examination commented in conclusion, that there were no observable preaccident deficiencies found with the cylinder. The stuck valve was consistent with combustion deposit buildup in the exhaust valve guide. 

Additional Information

Maintenance Actions

Lycoming Engines published Service Instruction No.1425A, dated January 19, 1988, which outlines Suggested Maintenance Procedures to Reduce the Possibility of Valve Sticking, and is applicable to all Lycoming direct drive engines. The Service Instruction comments in part, that "Investigations have shown that exhaust valve sticking occurs more frequently during hot ambient conditions. The lead salts that accumulate in the lubricating oil from the use of leaded fuels contribute to the deposit build up in the valve guides. This condition is eliminated each time the oil and filter are changed. Depending on the amount of deposits, sticking between the valve stem and guide can restrict the valve movement, which is often identified by an intermittent engine hesitation or miss." Textron Lycoming recommends 50-hour interval oil change and filter replacement for all engines using full-flow filtration system and 25-hour intervals for oil change and screen cleaning for pressure screen systems. (Refer to Service Instruction 1425A, which is appended to the docket for this report.)

Lycoming Engines published Mandatory Service Bulletin SB-388C, dated November 22, 2004, which outlines Procedure to Determine Exhaust Valve and Guide Condition, applicable to all Lycoming direct drive engines. Time of compliance depends on the engine use as follows:

Helicopter Engines – 300-hour intervals or earlier if valve sticking suspected.

All Other Engines – 400-hour intervals or earlier if valve sticking suspected until exhaust valve guides are replaced with guides made of improved material. At the time of the accident the engine had accumulated a total of 324.1 hours since the last mandatory inspection of the exhaust valve and guide inspection, which was less than the required number of hours as outlined in SB-388C. (Refer to SB-388C, which is appended to the docket for this report.)

Lycoming Engines published Mandatory Service Bulletin SB-480E, dated April 13, 2005, which outlines Oil and Filter Change and Screen Cleaning, applicable to all Lycoming direct drive engines. This MSB requires 25-Hour interval oil change, pressure screen cleaning, and oil sump suction screen check for all engines employing a pressure screen system; the subject engine utilizes a pressure screen, not a full flow oil filter. An examination of the engine and aircraft logbooks revealed that the most recent oil/filter change/inspection was performed on June 21, 2017, at a tach time of 702.1 hours. The tach recording observed at the accident site was 756.5 hours, which computes to 54.4 hours since the airplane's most recent oil/filter change/inspection was completed and therefore was not in compliance with the Mandatory Service Bulletin. (Refer to SB-480E, which is appended to the docket for this report.)


With respect to the Service Information 1425A, and Mandatory Service Bulletins SB-388C and SB-480E as previously discussed, a review of maintenance records revealed that no entries were observed to indicate that any of the three had been complied with. According the FAA Order 8620.2A, National Policy, Applicability and Enforcement of Manufacturer's Data, it states in part, "…unless any method, technique, or practice prescribed by an OEM in any of its documents is specifically mandated by a regulatory document, such as Airworthiness Directive (AD), or specific regulatory language such as that in Federal Aviation Regulation Part 43.15(b), those methods, techniques, or practices are not mandatory. (Refer to FAA Order 8620.2A, which is appended to the docket for this report.)

NTSB Identification: WPR17LA175
14 CFR Part 91: General Aviation
Accident occurred Tuesday, August 01, 2017 in Phoenix, AZ
Aircraft: GRUMMAN AA1, registration: N6216L
Injuries: 2 Serious.

This is preliminary information, subject to change, and may contain errors. Any errors in this report will be corrected when the final report has been completed. NTSB investigators may not have traveled in support of this investigation and used data provided by various sources to prepare this aircraft accident report.

On August 1, 2017, about 1300 mountain standard time, an Grumman AA-1B, N6216L, was substantially damaged following impact with terrain shortly after takeoff at the Deer Valley Airport (DVT), Phoenix, Arizona. The airplane was registered to a private individual and operated by the pilot as a 14 Code of Federal Regulations Part 91 instructional flight. Both the flight instructor and student pilot sustained serious injuries. Visual meteorological conditions prevailed for the local flight. No flight plan was filed. The flight was originating at the time of the accident.

According to an Federal Aviation Administration aviation safety inspector who responded to the accident site, several witnesses reported that after the airplane lifted off and was in its initial climb to the west, the wings started to rock back and forth. The airplane subsequently began to descend, struck the airport's western perimeter fence, and collided with terrain before coming to rest on a road that borders the airport on the west. Both wings and the engine had separated from the airplane due to impact forces. The wreckage was recovered to a secured location for further examination.


Chandler Riesterer's recovery fund: https://www.gofundme.com

RotoProne Therapy System, a special bed Chandler Riesterer is in.


Brody Burnell's recovery: https://www.gofundme.com



Brody Burnell (left) and Chandler Riesterer (right) on one of their many flights together. The pair were critically injured when their plane crashed near Deer Valley Airport in Phoenix on Aug. 1, 2017. 



SCOTTSDALE, AZ - The Dutch Bros located near Scottsdale Road and Thompson Peak Parkway in Scottsdale is donating proceeds to help two young Valley residents that were involved in a plane crash recently.

Earlier this month Brody Burnell and Chandler Riesterer were involved in a small plane crash near Deer Valley Airport. Both are still in the hospital in critical condition and face a long road to recovery.

“We are deeply saddened by the accident these young men were involved in,” said Dutch Bros Phoenix General Manager, Josh Hayes. “We want to do what we can to help support them, and their families during this time of need.”

While only one location is donating proceeds Friday from purchases, all Valley locations will also have a donation bucket that goes directly to the family.

Brody had been working at the Dutch Bros location that is donating proceeds for two years.

“Brody and Chandler, they’re still fighting to keep alive at the hospital down there, and every bit of money that they can get is going to be super helpful for the families,” said Tyler Brooks, a regional manager for Dutch Bros.

“Both of them still have a lot to recover from and probably still have some more surgeries to go," said Megan Anderson, Brody's cousin.

She said both the two men fly planes, but Brody was the pilot that day.

“He’s wanted to be a pilot since he was 6," Anderson said.

“We appreciate any and all support given and if you want to make a donation to the cause, we will be accepting contributions at every Dutch Bros location in Arizona,” said Josh.


Story and video ► http://www.abc15.com




It was a miracle they survived, and as 18-year-old Brody Burnell and 22-year-old Chandler Riesterer continue to recover in the ICU following a plane crash, a community is gathering to help the two, on their road to recovery.

"Both boys had all similar injuries between the head and the lower extremities," said Steve Burnell, Brody's father. "Broken bones and things."

Brody and Chandler were in a single engine plane that crashed last week, near 19th Avenue and Deer Valley. Brody was the pilor.

"I don't like to use 'miracle', but it's -- people are calling and praying from Wisconsin to West Texas to Florida," said Burnell. He also said Brodie met Chandler, another pilot, while working at a chain coffee shop location.

"That's how they met," said Burnell. "Came through the drive-thru, found out they were both pilots, became friends and started flying together."

Now, Brody and Chandler are recovering together, near each other in the ICU. Burnell said Brody's doctors  recently worked to lower the swelling in his brain.

"They did a, what they call a craniotomy," said Burnell. "They just took a piece of the skull off, and Mr. Brain is breathing and relaxing, and so, we can put that issue behind us, and move forward with the rest of his recovery"

As for Chandler, his best days happened recently.

"He's had, really, two great days," said Burnell. "His latest battle was Pneumonia, but they brought in a special bed, and was able to move him around and able to help things get better, and they did."

Two fundraisers are set to take place on Friday for Brody and Chandler.The "Chop" steakhouse in Chandler will donate their proceeds from open to close to Brody. Meanwhile, All Dutch Bros locations in Arizona are accepting donations, and the Dutch Bros off Greyhawk and Scottsdale Road will donate all their proceeds to the two boys.

They both also have GoFundMe pages set up.


Story and video ► http://www.fox10phoenix.com





Witnesses recount what they saw when a plane crashed near 19th Avenue and Deer Valley Road Tuesday afternoon.

​The Phoenix Fire Department said two men are in critical condition after a plane crashed near 19th Avenue and Deer Valley Road.

According to Phoenix FD, the Grumman American AA-1B Trainer aircraft went through a fence and lodged into a tree. Firefighters were able to get the men out of the plane.

According to fire officials, the crash happened off of airport property and close to Adobe Drive.

An FAA spokesperson said the pilot reported a problem shortly after departing Deer Valley Airport and said they would try to turn around to return to the airport.

Eventually the pilot and his passenger came down about a half mile from the runway.

Jade Byers works next to an airport, so it's normal to see planes from her office window. There was some very different about this plane though.

"Pretty low. Thought it might crash. Sure enough I heard a boom and it crashed right there on 19th Avenue," she said. I almost thought it clipped the building, or was going to anyway."

That's when Byers and several others working in her building ran outside to see if they could help. 

"Obviously working here every day it's in the back of your mind a little bit, but today it happened," she said.

Darrell Brethauer works at a body shop across the street.

"We heard a loud crash," Brethauer said.

He thought it was a car accident, but quickly learned it wasn't.

"Two guys were in the plane," Brethauer said. "We had to pull the tree limbs away so they could get to them. Then waited for the paramedics to get here."

The investigation and wreckage shut down 19th Avenue between Williams and Deer Valley for almost six hours.


The cause of the crash is unknown and Phoenix Police Department is investigating.

Story, video and photo gallery ► http://www.12news.com



PHOENIX (3TV/CBS 5/AP) - Authorities say a pilot and his passenger are critically injured after the crash of a small plane in north Phoenix just east of the Deer Valley Airport.

Phoenix Fire Department officials say the plane aircraft went down around 1 p.m. Tuesday and went through a fence and lodged into a tree alongside a road leading to the airport.

"The plane went down," said one witness. "I'm still shaking."

Pieces of the plane were scattered across 19th Avenue.

Two men were extricated from the wreckage and taken to a north Phoenix hospital by ambulance.

Their names and ages aren't immediately available.

"There were only two people on board," said Phoenix Fire Dept. Captain Larry Subervi. "Both patients are at John C. Lincoln North Mountain Hospital. They were both transported in critical condition."

Federal Aviation Administration spokesman Ian Gregor says the pilot of a Grumman American AA-1B Trainer reported a mechanical problem shortly after departure from Deer Valley Airport.

"We were talking about how low it was, and then it just started to wobble," said witness Taylor McCullough. "It just went straight down Our first instinct was to just pull over and get out and see if everybody was okay."

He says the pilot indicated he would try to return to the airport, but the plane crashed about a half mile from the runway.

There's no word yet on the cause of the crash.

Story, video and photo gallery ► http://www.azfamily.com



Two people flying inside a small, single-prop airplane were hurt when it crashed Tuesday afternoon in north Phoenix.

A Phoenix Fire Department official said two men were rushed to hospitals in critical condition after being pulled from the wreckage.

Both men were alert and communicating with first responders, according to Phoenix fire Capt. Larry Subervi. 

The plane went down just east of Deer Valley Airport, near 19th Avenue and Rose Garden Lane. It crashed through a fence and lodged in a tree, said Subervi.

Shortly after the plane took off, the pilot reported a problem with the plane and said he would attempt to return back to the airport, said Ian Gregor, an Federal Aviation Administration spokesman.

The plane went down a half-mile after the runway ended, he said. 

"Nineteenth Avenue is the end of the Deer Valley runway, so the witnesses that were there said they saw the aircraft swirling, and start to go down pretty immediately," Subervi said.

"I would expect this intersection to be closed all day," he said. "From here, Phoenix Police Department is going to do the investigation."

Subervi said the intersection is "extremely busy" during the middle of the day, and it's lucky that nobody else was hurt.  

http://www.azcentral.com

















PHOENIX - Phoenix Fire Department officials have confirmed a small single-engine plane has crashed in the area of 19th Avenue and Deer Valley Road, just east of Deer Valley Airport.

According to a brief statement by the Phoenix Fire Department, the plane went through a fence and lodged into a tree, where firefighters were able to extricate two people.

Video from the scene showed neighboring businesses did not appear to have suffered any damage as a result.

"Two adult males were transported to an area hospital in critical condition," stated Captain Larry Subervi. "The exact nature of their injuries is unknown at this time."

Federal Aviation Administration spokesman Ian Gregor says the pilot of a single-engine Grumman AA-1 reported a mechanical problem shortly after departure from Deer Valley Airport. He says the pilot indicated he would try to return to the airport, but the plane crashed about a half mile from the runway.

The names of the pilot and passenger have not been released.

Story, video and photo gallery ► http://www.fox10phoenix.com

No comments:

Post a Comment